Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

How to replace belt on Dyson DC17

\015 How to change a Dyson DC17 belt\015

Answers :

Preface: Dyson folks were great, answer so simple I was embarassed after I called. 5 minute fix.
1. Loosen 3 screws from bottom plate using flathead screwdriver or coin edge and remove it.
2. Wiggle roller until it pulls straight out.
3. Squeeze new belt and loop it over metal drive gear (you'll easily see the gear).
4. Keeping belt on gear, insert edge of roller through belt and rotate the roller while pushing it through belt until it is inside the belt, then continue rotating roller and sliding it over until belt is in position over gears on roller.
5. Insert roller into slots on that it came out of, reattach bottom cover and its done.
Bad news regarding all Dyson's. You can't replace just the belt your self. You have to purchase a new belt assembly which includes the gears. And it wont be cheap. I would call it a design flaw but i am sure that dyson calls it a profit scheme.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to replace drive belt on dyson dc17 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Here is a link to the belt you need and a manual you can view which has instructions: Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Where can you find a belt replacement for dyson dc17 animal and how do you replace the belt


Contact Dyson directly and they will ship you one for free but i would take you unit in because they changed the brush style due to a defect(would cause belt breaks often). They went from a thin belt to a thicker one so the brush is wider too and if ... Vacuums

How to replace belt on Dyson DC17


Preface: Dyson folks were great, answer so simple I was embarassed after I called. 5 minute fix.1. Loosen 3 screws from bottom plate using flathead screwdriver or coin edge and remove it.2. Wiggle roller until it pulls straight out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Belt broke on my Dyson Animal DC17 & I need to replace it. How do you replace it & can you get them at Lowe's where we purchased the vacuum?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do I replace the belt on the DC 17 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Call Dyson first - it may be under warranty and they send you not only a belt but a new brush system also - we just did that and our Dyson is about 4 years old. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do I replace the belt? - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson.Please call our Helpline on 1866MYDYSON. If you have a broken belt, there may be a problem with the clutch so one of our advisors will be able to run through some simple checks with you over the phone and talk you ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC17 Animal make a loud whine when engaging the brushroller. Metal roller fell out from bottom. What is it how do I replace it. It looks like it was a part that maybe provided tension to the belt?


You have plastic melted down in the brushroll housing and you will have to either try to cut the melting out or replace the housing. either way you will discard the pulley and replace the belt with the new wider belt. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Cant replace belt on dysonDC07 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


It is difficult to replace the belt yourself and you need a special tool to access and remove the clutch (the belt sits around the clutch and the brushbar). The best solution is to call the Dyson Helpline, they will refer you to an authorized repair ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

DYSON DC17 HOSE REPLACEMENT - Dyson DC17 Replacement Suction Hose, Part 911645-02


... Dyson DC17 Replacement Suction Hose, Part 911645-02

Replace belt and dyson vacuam cleaner, model dc14 I ordered a new belt and brush replacement assembly and we can't seem to understand how to get it apart to change it


If the DC14 has a brush protected aspect i.e. a switch on the front that puts the drive belt off, the drive belt would have to be replaced by a professional repairer as this can't be done at home. \015\012\015\012If the model doesn't have the b ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Belt replacement Hello, The belt that drives the beater bar on my Dyson DC-07 just broke. Is it that difficult to replace it or should I take it somewhere. Thanks!


It's a fairly simple job. The belt just loops over the end of the beater bar and motor shaft. Need to take the cover off the beater bar housing to get to it. Most difficult part is stretching the belt while putting the beater bar back in the housi ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Replace belts Buy and replace belts on my Dyson Animal


1-866-MY-DYSON(1-866-693-9766)Here is the contact #, I searched the entire site and did not see the belts. Maybe you should call and see if they are special order or something. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Changing belt on a dyson DC17 Animal - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


This video should help you out. \012\012 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to replace the power cord on Dyson dc17 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Replace belt how do you replace the belt on a Dyson DC14?


Hi its Darran at Dyson.So that we can help you with this query, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US).Kind regardsDarranDyson Customer Service ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How to replace the power cord on Dyson dc17 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need to replace the brushbaron my DC17 Animal model Dyson. It's almost four years old. I can't find the correct part number on the Dyson Website and I can't seem to find a Dyson repair center in Albuquerque, NM. What are my alternatives? If I can't service this machine without returning it to Dyson, I won't ever buy another one.


Hi,\015\012\015\012The original Dyson part number for the brush bar (often called brush roll) is: 911961-01\015\012\015\012If you type the above part number into Google Products (click link below) you will get a list of suppli ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07 drive belt replacement


Hi.\015\012\015\012The other end of the drive belt the part you cant see goes to a clutch.\015\012The clutch unit has 2 belts one is clutch to motor the second is clutch to brush roller.\015\012You obviously look after your ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.


The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym


Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Changing the belt on a dyson dc17


Here is a link to the belt you need and the manual which has instructions on how to change the belt:Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0718 seconds