Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?
WAND HARD TO PULL OUT....
\015 I JUST WONDERED IF ANYONE HAD THIS PROB ON THE PURPLE ANIMAL DYSON. SOMETIMES I SEE THE VAINS IN MY FOREARMS POPPING WHEN I WRESTLE THE WAND TO USE.... :)\015\012\015\012BESIDES THAT... HOLY **** WAS THIS PURCHASE THE BEST EVER! NO SIGNS OF THE 4 DOGS THAT LIVE IN MY HOUSE!\015
I'm asumming that there is no damage to the hose or pipe here. I had this trouble a while ago and sprayed a little bit of furniture polish (from a can) onto the pipe when fully exposed. maybe WD40 will do the same job but i haven't tried it yet. Anyway, hope it helps you.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Wand in stowaway dyson is hard to extend. Seems like u have to pull 3 clips from grooves in 3 rings around wand to extend and shorten wand which is a struggle
Hi there, you should just be able to hold the telescopic wand in one hand, press the button and pull the whole length of the wand out to its fullest position. If the telescopic wand on your particular Dyosn is very stiff, you may need a r ... Dyson "Stowaway" Canister Vacuum Vacuum
The wand is hard to pull up
The wand on this machine get lots of tiny dirt and fine dust caught in the sliding tube that fits in the hose. You will need to take the hose at its cuff end where it meets the wand and press the two tabs to release the wand out, then take some spay ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Kenmore Intuition wand very hard to pull out of head.
No vaseline. You can use wd40 or silicone spray.Also check to see if the wand is bent out of round where it meets the handle ... Vacuums
WAND HARD TO PULL OUT....
I'm asumming that there is no damage to the hose or pipe here. I had this trouble a while ago and sprayed a little bit of furniture polish (from a can) onto the pipe when fully exposed. maybe WD40 will do the same job but i haven't tried it yet. Anyw ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Wand hard to pull out from my dyson dc17 upright vacum cleaner
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.
I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Telescopic wand My wife's Electrolux Oxygen has a telescoping wand that expanded and contracted. All one had to do was slide a button and the lower tube slid inside the larger upper tube. Now the button no longer moves whatever was inside to allow the expansion/contraction to happen. How do I fix this situation? The wand assembly hardly seems to be made with repairs in mind. This method of manufacturing is annoying. Thanks, Eric
... Electrolux Vacuums
I have the Dyson Animal and I just bought it in January and my hose does not work. Mine you pull the hard part out and once it reaches the end it will click off of the top of the vacuum. I cannot pull it out. It is stuck.
Dyson have a two year warranty, they are a really good company and I would recommend calling them and asking them to fix the problem. Better that than trying to do it yourself and you end up breaking it and then invalidating the warranty. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Wand i can not get the wand out. It is suppose to be a quick draw it wont even budge i had 3 people pulling on it and still will not come out. help
I just took my DC17 apart to determine the problem (noted above). Basically it seems like there is a 'nub' on the lower part of the extension wand. Actually, there are two on either side, one higher (white, facing the back) than the other (black, fac ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Self propelled vac: goes great on hard floor or hard slick carpet. Goes backwards fine but will not pull itself forward very well. Requires some effor to push it forward. I have adjusted the cable so the lever on the motor goes as far forward as possible. Suggestions? Model U6446-900
Dear Nasherrill,\015\012\015\012I've found a friend! I thought I was the only person in the world who owned the Hoover Model U6446-900! This model does not appear on the http ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My daughter pulled to hard on the ceiling fan pulling out the chain. i have taken it off and apart, nothing appears to be broken but im trying to figure out how to put it together so it retracks, i assume it has something to do with the tension of the small spring inside of it, but not sure how to put it back together im wondering if there is a internal diagram of this ???
Don't even bother to repair the pull chain switch, get a new one at KMart, HomeDepot or similar store for less than $2.\012\012Two times I've repaired one, it comes apart when I need it the most.\012\012Good Day! Don't forget to rate thi ... Vacuums
The power cord is stuck part way out - it seems to have slipped over the edge of the reel inside the machine, so it won't pull out and it won't retract. Pulling hard does no good.
Hello,Yes, pulling hard is not a good idea. You need to use techniques to get it out.Get a flat Phillips screw driver, use it to bring it out. Or use a screw drive to disassemble the part that that went inside the machine. If ... Vacuums
Can't find info for hoover steam vac spin scrub model # F5905900 on Hoover website, doesn't show that model number at all...looking for mesh (kind of cone/cylinder shape) that goes in dirty water tank (I think) and also the tool (wand) that slides into front to clean it out. It doesn't pull all the water up very well and the filter has been missing for some time. I don't know if that has anything to do with it or not. As far as the wand tool goes, I have taken the cover off at this point and
The cleanout tool is part # 43514001. The filter is # 90001398. Be sure to leave a 1/2 inch gap between the top of the filter and the bottom of the lid. If you need a manual, try model F5914-900 0r F5912-900 on Hoover.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hose attachment On my dyson dc 25 the hose attachment is very hard to pull off. It seems like something is getting hung up when i try to pull up the hose.
Your wand is getting stuck in the hose because the hose is twisted - you need to unwind it:\015\012\015\0121) Pull the wand up as far as you can, all the way if possible\015\0122) Stretch the hose out and unwind it, use some babypow ... Dyson DC25 All Floors Bagless Upright Vacuum
Kirby runs across floor on own and is hard to pull back
... Kirby Ultimate G Bagged Upright Vacuum
Vacuum will only start if I pull out the cord very hard
The Miele interior is not too complicated. Look at this site for some instructions on opening it, http://www.sannerud.com/house/miele.html Then use visual inspection or an ohm meter to find out where the connectivity problem is.hope tha ... Miele S514 Solaris Bagged Canister Vacuum
Hose in DYSON too tight and hard to pull out
The problem is not a twisted hose. The hose itself is way too stiff. It pulls the vacuum around instead of expanding to reach. I hate this hose and it's too bad, because the vacuum works well, but trying to use the hose attachment it futile becaus ... Dyson DC25 Vacuum
Cannister is hard to pull
You charge all this money to buy your product and then you charge to answer the guestion WHAT KIND OF RINKY DINK OPERATION R U RUNNING IF U DO NOT HAVE THE ANSWER WHY ARE U SELLING YOUR PRODUCT I NOT SURE IF U GRADUATED FROM THE FIRST GRADE OR NOT O ... Rainbow E series Canister Wet/Dry Vacuum
Unable to pull the telescopic wand out - something holds it in place.
Hi Jane,I'm sorry to hear you're having difficulties with your DC17. If the wand seems to be jammed in place, I'd encourage you to get in touch with us directly, as we'll be able to talk you through the process of freeing it over the phone. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
, how do i release the tension so it's not so hard to use
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!
I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was f ... Dyson DC07 Bagless Upright Cyclonic Vacuum
How do I pull the wand out of my Dyson Animal? I lost my instruction manuel
If you look at the top of the machine you should see a button close to your handle on some models it is silver push it and it should release the wand ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The nub on my Infinity, has broken off, and now I can' push or pull without the wand coming up out of it's place, and/or twisting around. I love my cleaner, but not like this! What to do?
I have to vacuum with the other handle(on canister) while breaking my back,and it sucks. this happened to me also but i spent good money on the thing and i have just learned to vacuum this way! ... Euro-Pro NV31 Infinity Vacuum
Nilfisk sd4 polisher/scrubber pulling hard to one side. any ideas thanks pat
... Nilfisk Vacuums
On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?
This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum