Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

Wand will not ****--

\015 My vacuum works well except the suction on the wand is completely not functioning and that is what I use the most to get up pet hair--\015

Answers :

It's clogged run water through it. or stick a broom handle or something that will fit in it through, that should do it.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When connecting the wand into the brush component. sporatic power (sometimes runs sometime nothing) the power is on again off again. when hold pressure down on the wand the power stays on. do you think the coupling connection is bad on the wand? would the wand replacement likely be the culprit?

There is is switch or sensor in the connection. Likely that piece is worn or shorted out. You may be better off getting a new wand piece ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Need connector wires inside wand. Electrolux central vac. 16" wand 1 1/4" wand dia. Don't need wand, just the wires.

Go to a store like Lowe's and look in their electrical department. You need wire the same gauge size (stranded or solid) and comparable insulation. Hope this helps! ... Vacuums

My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.

... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a Infinity Vacuum Cleaner. Shark Model NV32. I took the wand out to vacuum a spot and now I can't put wand back in. I keep pressing the wand release button when putting the wand in but no good

... Vacuums

Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!

... Dyson DC05 Bagless Canister Cyclonic Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C

... Filter Queen Majestic Canister Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after

... Vacuums

HI, I have a Kenmore 25813 and it seems like there is an intermittent short. When I have the extension wand on and the power floor attachment on, when it rotate the wand the light cuts out and so does the power floor attachment, when I twist it back it comes on again. I don't have this problem if I remove the wand and just use the crevice tool with the hose. Any idea where the short might be and can I fix it myself? Thanks. Gary

This is common you may have a short in the contacts from the handle to the wand or a break in the cord that goes into the powerhead ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?

... Euro-Pro NV31 Infinity Vacuum

The hose does not stay connected to the wand although the collar appears to be locked in place for a while. Is there a replacement part for this? Also the holder where the wand goes in has split horizontally. This appears to be one piece with the body of the unit. Is it repairable? It still holds the wand but continues to get worse.

... Dyson DC07 Bagless Upright Cyclonic Vacuum

Telescopic wand My wife's Electrolux Oxygen has a telescoping wand that expanded and contracted. All one had to do was slide a button and the lower tube slid inside the larger upper tube. Now the button no longer moves whatever was inside to allow the expansion/contraction to happen. How do I fix this situation? The wand assembly hardly seems to be made with repairs in mind. This method of manufacturing is annoying. Thanks, Eric

... Electrolux Vacuums

I have a beam adjustable wand with an attachment on it meant for hardwood, or linolium floors. The wand is broken so I would like to take the attachment off and put it on a new wand. How do I get t

... Beam Vacuums

I have the dyson animal. There is something stuck in the wand tube and everyting is getting caught on it. There is very little suction from the wand. How do I get the wand apart or somehow get the object stuck out of the tube? Thanks

Yes, things stuck in vacuum hoses are not always as easy to remove as one might think. Trying to push it out with something can be counter-productive, and only get the thing stuck tighter! If you have a second vacuum, you can try sucking it out the w ... Vacuums

Wand in stowaway dyson is hard to extend. Seems like u have to pull 3 clips from grooves in 3 rings around wand to extend and shorten wand which is a struggle

Hi there, you should just be able to hold the telescopic wand in one hand, press the button and pull the whole length of the wand out to its fullest position. If the telescopic wand on your particular Dyosn is very stiff, you may need a r ... Dyson "Stowaway" Canister Vacuum Vacuum

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand

My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It look ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

The wand will not stand up on its own when attached to the vacuum head. I had earlier models which did not have the adjustable height and this was not a problem--I simply turned the wand to the side. But I cannot do it on with this wand. Any solutions?

Hello. There is a small part on that wand which enables it to stand up on it's own. It sounds like yours is worn or broken. Take it to your local vacuum repair store and they will have you back up and standing in no time. The part is about ten do ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

I bought a used Miele vacuum with the SET210 wand, but the push button to release and clamp the telescoping wand was missing. I can get the wand to slide by pushing with my finger, but it's a little difficult. The main problem is that nothing holds it in place at the desired position. I bought a replacement push button online, but it came with no instructions. How do I install it?

Your best bet would be to put on your friendly face, and take the unit into a Vacuum Repair Shop, and have them assist you, or at least give you tips on the procedure. Chances are you will have to disassemble the unit a lot more than you might want ... Vacuums

The hose with wires still attached has disconnected from the wand inside. How do you reattach the hose to the dc22 telescopic wand?

... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

DC17 wand release catch won't release. wand stuck

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Metal wand came out of wand handle - won't reinsert

... Dyson DC14 Low Reach Bagless Upright Cyclonic Vacuum

I have a 116.28614801 Kenmore vacuum cleaner. The Powermate connection to the wand is shorting - arcing - changed wand still happening. Any Solution?

... Kenmore Vacuums

My Dyson DC 18 has no suction in the wand. it is in the upright position and the wand and hose is cleared from debris.

... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

My telescopic wand height adjustment won't lock the height in place. The wand extends to full height with no locking in place. How do I fix it?

These wands have a very small nub that locks them into place. They wear out very easily. You might have to replace the wand. ... Euro-Pro NV31 Infinity Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0181 seconds