Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

The beater bar makes a loud noise and something is cutting into on the end opposite of the belt. I have taken it apart and cannot find anything that appears to be out of place. Lynnette


Answers :

Check to see if the belt is missing any gears. If it is then that is your problem. anothe issue might be that the roller bearing is loose or missing. you will be able to see this when you take off the bottom plate. let me know if this helps.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The beater bar makes a loud noise and something is cutting into on the end opposite of the belt. I have taken it apart and cannot find anything that appears to be out of place. Lynnette


Check to see if the belt is missing any gears. If it is then that is your problem. anothe issue might be that the roller bearing is loose or missing. you will be able to see this when you take off the bottom plate. let me know if this helps. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Shark lift away won't seal, sucking out the side hole, but not out of the bottom, I have taken it apart, can't find anything wrong.


... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Have DC07 that won't come on. Wife said this started happening a few weeks ago. Would come on and then other times would not come on. Now will not come on at all. Believe I have a lose wire. Have taken off star screw by on off switch, but cannot find how to get plastic parts apart to get into electrical connections. How do I do this? I am sure I am missing something simple?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi, I vacuumed a small rubber bouncy ball up into the vacuum by mistake. The suction is not as strong now, and I'm not sure what to do. Where I can easily take the hose apart (eg. at the handle places) I cannot find the ball. What do you suggeest?


... Vacuums

My roomba 550 makes loud clicking noises and stops after 5 minutes and tells me to check brushes. I have taken it apart as much as possible and cannot find the problem


Pull brush rollers out.pull funny lookin yellow ends off and clean hair ect.out .also pop out front wheel and clean ... iRobot Roomba 550 Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Kenmore bagless intelliclean vacuum is making a loud noise mainly when it is vacuuming on the highest setting (when the light is red). We have taken it apart and cannot find a clog. It has also lost suction.


This might help, it was posted on a previous problem but is the same issue you are having it seems: "Here is a possible solution. If the v ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

We have the bissell pro turbo with heater and we cannot get any suction for the water. took completely apart and couldnt find anything.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

We have a dyson dc25 - there is no blockage but it won't pick up using the hose. The upright part is absolutely fine. We have taken it apart and cannot find a blockage - help


Try taking the pipe off completely and blowing up it. This worked with mine ... Dyson DC25 Bagless Upright Vacuum

The bin latch came apart, 2 springs and cross piece that is the latch. I cannot find an expanded view and have no idea how to put them back . Nothing appears broken or cracked.


Click this link for instructionshttp://dysonmedic.co.uk/replacing-dyson-dc07-cyclone-bin-flap-catch-clip/ ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My shampooer is not putting out soap in a steady stream.It is like it is clodded up. I have taken all the parts apart that I can and cannot find any clods.


The plastic screen which suppose to be attached to the shampooer tank (under the dial) is probably stuck in the hos remove it from the hose and attach it to the tank. See if you put correct proportions of shampoo and make sure that water is warm. ... Kirby Ultimate G Bagged Upright Vacuum

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne


... Hoover S3614 Vacuum

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

I had to replace the idler arm assembly because it snapped. I then had to put the torsion spring in place and that is where I am having trouble. I cannot seem to find a diagram that shows how it goes back into place.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

It's been awhile since I have used my shampoo system on my Ultimate G series Kirby. Well, as instructed I took it apart and cleaned it. Now I can?t figure out where to put the ?screen cap? and ?sponge filter?. I have my manual in front of me and the only place it shows the filter and sponge (page 35 in the manual) is when it?s been taken apart to clean. It doesn?t show where to put it back. I don?t know what I would do without all the pictures in the Kirby manual. HELP! Thanx. Visual Kirby Vacuu


Hello,\015\012The littlew round screen goes in the hole where the hose attaches to the tank. The round foam filter goes up in the hole underneath the on/off valve for the foam. Here is a guide if you need any more help...\015\012\01 ... Kirby G6 Bagged Upright Vacuum

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?


Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak


... Kenmore Progressive 35922 Bagged Upright Vacuum

I have taken delivery of a new Lloytron Halogen Oven E4701 WH.from a supplier in the UK (I live in Spain). On unpacking it I found that Part of the temperature control knob assembly had fallen down inside of the heater body. I dismantled the heater body to retrieve the part but I cannot now work out the order of re-assembling the fan parts so that the fan does not catch on other parts of the assembly. I cannot find a parts drawing on-line. Can you help ?


... Vacuums

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

I have just receiived my "GAMUCCI MICRO V2 STARTER KIT RECHARABLE ELECTRONIC CIGARETTE" it wpould appear that there is a part missing. as I find that I cannot insert the cartridge.. the cartridge as illustrated in th manual appears to be missing. there fore i canot fir the inhaler part of the cigaret.


Panuh pu ba matatanggal ung engkanto sa bahaii?? ... Vacuums

No suction I cleaned and checked all hoses, sounds like something is stuck inside, like a sock, took machine apart as much as I could and couldn't find anything. Any suggestions?


Ok first thing to do is remove & clean the 2 piece premotor filter or purchase new.Now remove soleplate from bottom of machine to do this rotate the 3 plastic screws to unlock position. Lift sole plate off now remove any blockagers or ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I smell dust coming from my Riccar N2000 upright vacuum. Repairman cannot find anything wrong. What can I do?


... Riccar Vacuums

My dyson makes a noise every few seconds that sounds like a very loud 'squeal', or a giant budgie chirping! It's still picking up ok. I've taken it to bits and cleaned it, but I cant find anything wrong. Help.


Hi thereNot sure what is causing this, it could be that the belt that drives the clutch and brush bar is wearing so is slipping (like a fan belt on a car). If this is the case, we could arrange for this to be repaired. Call ou ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Turbo EmPower 4600 and the roller will not turn when we turn on the vacuum. The vacuum is fairly new, and hasn't seen too much use, but now the roller won't turn, so it's not picking anything up. There also doesn't appear to be a belt or any way to take this apart. Can you help me? Thank you!


The beater belt is broken. There are 4 phillips head screws on the outside (2 on top of the base on either side of the upright, and 2 on the front edge on the underside of the base near front edge). and 4 phillips head screws on the inside (holding ... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0557 seconds