Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

Motor in overheating . I do not find any blocages


Answers :

The motor overheats because it get's too much air, usually caused by missing filters, or filters that have large tears or holes.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor in overheating . I do not find any blocages


The motor overheats because it get's too much air, usually caused by missing filters, or filters that have large tears or holes. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a hayward 1HP superpump with an Ao Smith UST 1102 motor on it. Last year I had a leak in the pump, and I believe I got some water in the bearings of the motor. Over the winter I replaced all the seals in the pump, and have no leaks this year, but the pump is sounding pretty loud since opening the pool this year. I have (2) fold question: (1)I can not find any information on the where I can find a replacement bearing for this pump. (2) I can not find a procedure on HOW to go about


Hello. I get my parts here http://www.poolcenter.com/parts_pumps_hayward_superpump.htm\015\012\015\012Joe ... Vacuums

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Bissell PowerForce Turbo: The motor spindle becomes very hot while spinning, causing the new belt to burn and break. Is this because the motor is overheating?


Something is preventing the brush roller from turning even though it seeems to be OK when not in contact with the floor. The motor shaft is spinning on one spot of the belt, causing the heating, the smell, and eventual belt failure. I have had brush ... Bissell 6594 PowerForce Bagless Upright Vacuum

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Replacement motor I am undertaking the repair of an old dustbuster as a training exercise. ,The motor in my V2410 is Made by Johnson Electric but I cannot find reference to the numbers marked on it on the manufacturers website. Are you able to give me a model number for an equivalent replacement or the specifications of the original motor? Thanks, Gary.


... Black & Decker V2410 DustBuster Handheld Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n


From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

I have a kenmore canister model number 116.2645083 I need a replacement motor. I was given 2 different numbers: 1. 4147248 2. AC92FAUX200 I can find the 2nd motor, but it doesnt have the 4 wires like the original one. Can you tell me if this is the right motor? Thanks Becky


Greetings from GoVcauum.com,\015\012\015\012Ok, so good news, I have looked up your model number for your Kenmore vacuum and found that your Kenhmore canister takes the motor ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Motor my motors packed up where can i find where the motor goes as got a new one


The moter goes under the dust bin and not that easy to get to only if you known what your doing hope this as helped you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Motor started making a grinding sound and has a burn order. I found a site that sells parts such as motor assembly but I can not find a repair manual to provide disassembly instructions. It does look like this is a direct drive unit, that is no belts, at least none that a user can relace.Know of any repair manual sites? It is a Hoover F5899-900 SteamVac


... Hoover F5899-910 SteamVac Vacuum

I'm trying to find a part number for the motor on a 113296200c, craftsman wet/dry vacuum. Sears could only provide part number 09 113826404 for the model number 113296250c. I have found motors with the model number 826404 on ebay, however no one can confirm if this is compatible. Can anyone help me out here?


... Craftsman 17026 Wet/Dry Vacuum

No power when turned on, I checked motor brushes and they are almost worn out, could this be the problem? and where do I find replacement brushes? I have checked on Dirtdevil's site but I don't see any motor brushes. I am in Montreal, Canada. Thank You.


Hi,\015\012Before that I wouild check the switch...the switches on those things go bad regularly...get a meter and check the power on either side of the main switch and I think your problem will be there...\015\012\015\012heatman101 ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

I have a TriStar LEC vacuum and today I turned it on and for a split second the motor whirred and then nothing. Now it won't come on at all. I cannot find any way to access the motor.


How do i replace the power cord on my lec tristar vaccum? ... Tristar Vacuums

I have a mile tt2000 that works fine up to 1300W but if I crank it up higher the motor decreases and increases speed every couple of seconds. I have changed the bag and filters and done the usual cheCks for blockages but can find nothing amiss. Unusually when it is running and I block the intake it will run at full power but as soon as I clear it the motor "hunts" again. Any ideas.


... Miele Cat & Dog 326i Bagged Canister Vacuum

Rick E1, it looks like the Motor Pulley, Elna #440152-20 needs to be replaced on my 722010 model (flat on one side from standing around. It looks like some kind of a set screw which keeps it attached but are you familiar with how to get this item off the little shaft it is on. Also, any idea where I could find a reasonably priced Motor Pulley.


... Vacuums

Motor sounds loud and high pitched. Suction seem ok, can't find any blockages. Cleaned filter at top of removable canister. Exhaust seems hot and low. Can there be a blockage within the motor housing?


Most likely your bearings are shot. it will need a new motor ... Kenmore Vacuums

The motor is overheating and shutting off -- after vacuuming for a short time the vacuum motor shuts off


Sounds like there is a clog somewhere or a filter needs to be cleaned if it has one. Or the bag may need emptied.Jim ... Vacuums

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We own a dirt devil model 088600, and are experiencing a problem with the belt wearing away a section between where the belt connects to the brushes and the motor. There is a lot of plastic/rubber residue coming out from the vacuum. We have tried new belts only to find the same problem occurs. I noticed that the source of the dust is coming from the section between the brushes and motor, where there appears to be a section that is misshapen and melted. I looked up the schematic online and can't


If you are certain that the belt is seated correctly and the beater bar is nested in its holder and the cover of the assembly has been properly installed and you still see a contact area between the belt and cover, you should either: return the vac ... Dirt Devil Vacuums

I have an old silver king cannister vaccum (R2-D2 star wars) Im looking for filters. When you take machine apart there is a donut looking filter under motor(top of vaccum) that protects motor. I cant find them anywhere. I found the other filter the model uses (disc filters) HELP!!!


I'LL DO A SEARCH ON LONE BUT THE MODEL NUMBER WOULD HELP ... Vacuums

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re


Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0464 seconds