Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?
Corner of the rug sucked in and the roller now does not spin
\015 I don't know if the motor burnt or not the but the rotating main cylender is not spinning anymor. the belt on it is fine but does not turn. there was no smoke or smell either it was couple of seconds only..\015\012any ideas??\015\012thanks in advance for your help.\015
If you can't hear the motor running, look for a reset button which may have tripped. If the motor runs, remove the belt and look for a burned spot that might be preventing brush turning. Replace it if it is. Make sure that the wall outlet has power (check with a lamp). Hope this helps!
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Corner of the rug sucked in and the roller now does not spin
If you can't hear the motor running, look for a reset button which may have tripped. If the motor runs, remove the belt and look for a burned spot that might be preventing brush turning. Replace it if it is. Make sure that the wall outlet has power ( ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The brush stopped revolving. I don't see anything blocking. It sucked up a corner of a rug for a split second but didn't pull anything off of the rug, ie, nothing from the rug is in there. Do these have belts? I don't see that. vicki
Although I do not share the exact same model that you have, there is a belt in the one I own. \015\012\015\012Checking it was pretty easy as the unit comes apart in a simple manner.\015\012\015\012I do not know how your unit comes apart b ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum
Roller brush stops spinning and vacuum makes noise. Brush will spin normally ok, until you use it on the rug.
That means that the belt is stretched and can't turn the brush against the resistance of the carpet. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes
Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The vaccuum is not picking up especially on rugs even though the roller is spinning. The hose has tremendous suction/.
... Dyson DC14 Bagless Upright Cyclonic Vacuum
Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?
After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums
I have a Eureka SurfaceMax 300 yellow one and its not sucking up very well at all, and its blowing dirt and dust out the back?? my ol man checked tonight and said the roller isnt spinning, so if i jus
Here is the manual , check belt is not broke, and the pipe behind the brushbar is't blocked up,http://www.eureka.com/FileLibrary ... Vacuums
The problem started when i sucked a corner of a rug,now it will not **** very much at all??Kenmore upright progressive
This definitely sounds like your belt is broken. The belt is the part that is attached to the motor at one end, and to the roller brush at the other end. If something gets vacuumed up into the brushes that prevents the brushes from spinning, the ... Kenmore 34612 Bagged Upright Vacuum
No Suction Something made a pop and my dirt devil featherlite is not sucking anything up. The roller brush is still spinning and the belt is good. What's the possible problem?
It is probably the dirt fan. u may have to get it serviced ... Dirt Devil Featherlite Bagged VacuumVacuum
Beater bar sucked up corner of throw rug and now it doesn't turn.
Take the head down and clean the brush and when you put it back together it should be back in sync. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a Panasonic Performance plus MC-V5217. Something got stuck in the rollers and it stopped spinning. We've cleared the brushes but can't get it to spin. Is there a reset button?
Bottom roller bush does not spin
Sounds as if the v-belt came off the idler arm or you broke the v-belt. Either way, take the 4 screws out of the plate around the roller brush and make certain the belt is there and that it sits on the idler wheel. If you remove the roller brush yo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Vacuum cleaner roller won't spin but everything else looks okay
Hi, if the roller isnt spinning then the usual cause of this is going to be that either the drive belt has stretched and is spinning without turning the roller or the drive belt could have snapped what you can do to find out is like the vac on its ba ... Vacuums
The roller wont spin when I lower the handle
Hi its Darran at Dyson.It is possible that the item has caused some damage to the clutch. We would advise following the onilne checks at www.dyson.com and clikcing on the support section.If this doesnt resolve the issue, plea ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?
The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum
The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not
... Riccar 8850 Vacuum
My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.
Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum
I ran over a big floor rug with my vacuum and some of the strings from the rug got tangled in the roller on the vacuum. It makes a terribly loud noise even now after I have cleared the strings from the rollers. What else can I do to get rid of the loudness?
Loose area rugs should never be cleaned with any revolving brush vac. They will damage the rug by destroying the fringes and corners. In some cases the brush will also pull out tufted as the rug is made so poorly. Natural fiber rugs should never have ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The roller that spins with little brushes stopped suddenly and no longer spins. I pressed the red little knob at the end of the roller but it doesn't fix the problem.
Open up the roller area check to see if somthing got picked up and jammed into the rollers so that it can't work, a rock or a screw or you might even have a large amount of string or fibers wrapped around the shaft or brush keeping it from rolling ... Dyson Ball DC24 Bagless Upright Vacuum
No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Roller problem Roller keeps stopping. I've emptied the dustbin. removed the roller to see if it is clogged, but appears to be nothing impeding it. It stops on a short napped rug, and even on the wood floor. Is the spool that the roller slips into driven by a belt? Can I get in there behind the spool?
I have 3 Prontos, one in each part of the house. Two of mine had the rollers stop. I figured out the problem and it fixed both. Take the roller out by turning the plastic screw and popping the plate off. Pull all debris off the wheel that turns. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum
My dirt devil easy lite cyclonic does not suck up the dirt or anything on the floor anymore the rollers still roll. It stop sucking.
Check and make sure that the pickup tube from the bottom of the sweeper to the waste cup does not have a clog anywhere you can use a metal coat hanger and straighten it out and carefully run that thru. ... Vacuums
Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand
In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I have a Royal upright metal vacuum. The roller stopped spinning. I took the roller off and the ends were full of dust and hair. I would like to take the ends of the roller off to clean more -- how do I do this?
... Royal 4000 Classic Bagged Upright Vacuum
Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?
The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum