Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

I accidentally sucked up a thin belt that wrapped around the bristles and stopped the bristles and now the bristles wont turn


Answers :

You need to remove the thin belt from the roller if you haven't already. Check the ends of the roller to make sure there is nothing there stopping the roller from turning. You can try turning the roller with your hand using minimal force.
\015\012
\015\012I believe this unit has a switch on the front of the handle for the brush motor. It may cut off if the roller gets hung up. Have you tried turning this on?
\015\012
\015\012In summary try cleaning everything off of the roller and then check for the switch that I mentioned. Let us know how you make out and good luck!
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I accidentally sucked up a thin belt that wrapped around the bristles and stopped the bristles and now the bristles wont turn


You need to remove the thin belt from the roller if you haven't already. Check the ends of the roller to make sure there is nothing there stopping the roller from turning. You can try turning the roller with your hand using minimal force. \0 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn


The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hi my hoover vacuum, stopped working,does not even turn on,I accidently went over a shoelace but stopped before the shoelace went in, ,,becuase of that the belt came off,and then i put belt back on, and now it wont even turn on


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

A cloth belt got wrapped around the roll and after taking the roll off and getting the belt off of it, now the roll won't turn when I turn the vacuum on.


Install new belt. You'll have to remove the botton cover and the remove the brush cylinder and install new bell. What happen when the brush cylinder stop because of the colth belt, it stripped the rubber kogs off the belt. The only thing that turn ... Dyson DC25 Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I have a windtunnel 2 vacuum. It sucked up a cord that wrapped around the beater bar. Now the bar won't turn. There was no smoke or sign of something burning. The motor still runs and there is suction but no turning. We have it apart but nothing is obvious. What should I check?


Check the actual beater bar for movement. I have seen the plastic melting, and bearings seized under such circumstances. Also I am unsure by your question, but the motor that creates the vacuum (sucking) is different than the motor that spins your ... Vacuums

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I sucked up a sock into the carpet attachment of my electrolux 3500 series and the carpet attachment cut off. After the sock was easily removed (it was only wrapped around the brush part) I reattached the carpet attachment, turned the vacuum on and flipped the switch to turn the carpet attachment back on, but it won't come back on. How can I fix it?


Did you press the reset button? There will be a reset button either on the back of the unit just below the bulkhead or on the top side of the base.\012\012Locate the reset button and press; this should allow the carpet attachment to resu ... Electrolux Epic 3500 Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Bristles quit rotating and smelled like something was burning. It isn't the belt that turns the bristles. Can't afford a repairman, can you help me fix it?


Belt can reamin intact but still jam and burn. It won't necessarily break. I suggest you remove the bottom of the vacuum where the bristles spins and where the belt is located. You may have something jammed in there. You may need to remove the bristl ... Bissell 6594 PowerForce Bagless Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

The rotatory brush stopped turning after sucking rug fringe onto it. The belt looks fine. The suction is fine.


Found on website "dysoninfo.com"A problem I have run into a couple of times at home, generally when I am cleaning the bathroom, is that my Dyson brush won't turn. First off I would say be sure to check that you haven't press ... Dyson Vacuums

A small thin antenna cord on my radio got sucked up, and I immediately turned my vacuum off and easily puled out the small cord, Afterward the brush on the vacuu would notrotate.. The belt is not broken on the vacuum is not broken. My husband cannot figure out what the problem is


Hi Susan. There may still be a piece of the cord in the brush roller bearing. Check the ends of the brush and have a look. If its clear the belt is probably strethed. An easy way to test this is to turn on machine a put you hand against brush, if it ... Riccar 8955 Upright Vacuum

I sucked up a sock and there was a burning smell. I immediately turned off the power, the sock was wrapped around the roller, got it off and let the vacuum cool. Now it no longer powers on. Is it dead or fixable?? Ann Marie Smith


The smelling could be the belt. Unplug the unit and turn it over, see if you can see the belt. Turn the roller to see if there is any wear on the belt. If the belt looks good, that is not good. If it does not turn on, there is no fuse or breaker ... Euro-Pro NV31 Infinity Vacuum

Halo beater bar has quit working. bar (that belt is wrapped around) connected to motor is not turning. have pushed reset button. k.r.


Take it to an oreck dealer. duh ... Vacuums

I have a Hoover linx cordless stick vac. I have not had it but several months and it has quit sucking anything up. It worked great when I first got it. I was so excited at how well it worked. It had gotten hair wrapped around the brushes but I got that out and thought it would work better. It is turning and sounds like it is working but it does not pick it up. I could use your help please. Keely


... Hoover Platinum LiNX Cordless Stick Vacuum

The vacuum sucks good, but the brush on the bottom wont turn, and the belt seems tight


Even tough the belt is intact it still might need to be replaced. Here is a replacement:Dyson DC14 Belt and Manual ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

It makes a loud noise when turned on. it doesn't make the noise when you use the hose. It looks like the roller on bottom is cracked where the belt wraps around it.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?


I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2743 seconds