Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?


Answers :

If the belt that drives the brush is not broken, check to see if the brush itself is stuck from turning.\015\012If is is, remove it and clean as best you can, paying special attention to the two ends. It might make sense to spray the hard rubber holders on each end with a bit of WD40 and manually turn them until they move freely.\015\012
\015\012If this information has provided you some assistance, I would appreciate a thumbs up rating in return.\015\012If you have any questions, please feel free to contact me.\015\012
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :


If the belt that drives the brush is not broken, check to see if the brush itself is stuck from turning.\015\012If is is, remove it and clean as best you can, paying special attention to the two ends. It might make sense to spray the hard rubber hol ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?

Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

DC07 brush wont spin on bottom, took all apart and wont work

Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Bissell 3750 bottom brush will not spin belt is fine and lift off works great

Hey Jessica! Please contact us for assistance regarding your vacuum.Here's a quick link to assist you:\015\012http://www.bissell.com/contact-us/?cid=ccsocial ... Bissell 3750 Lift Off Bagless Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

I cut all of the hair out of the bottom of the spin-brush on the Dyson Upright Animal Vacuum. Now I dont think I can get the brush back in there correctly. If I squeeze it in there (which it is a VERY tight fit...) then it wont spin. Any thoughts?

Check the roller ends for dirt build up, they pull off and you should be able to clean them out.\015\012The roller should just go back into place if pushed together. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Brushes wotn spin,belt not broken,cog that drives the belt is not spinning.When I turn the brushes manually I can occaisionally feel it grabbing for a a brief second.Could the motor be bad? Is there a way to test the motor.Tahnks

The motor is bad and this is a common problem with this machine. It is engineered very poorly. I would take it back and get a Dirt Devil Platinum Force machine. They have a great track record. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The brush stopped on our DC25. Husband said sparks were coming out of the bottom near where brush is. Brush was cleaned of hair and string. Brush still does not spin. I saw no belt on the brush. Should there be one?

... Dyson DC25 Animal Bagless Upright Vacuum

Brush wont spin, belt is perfect

It sounds like the motor that spins the beater brush is burned out,If it is under a yr old it should be covered by the manufacturer warretee. Find a Hoover service center that does warrentee repairs. ... Hoover U8188-900 Bagless Upright Vacuum

My vacuum's rug brush will not spin. the belts are fine and in place, but when i engage the carpet brush nothing happens. i looked under the bottom and there are no obstructions preventing the brush from opporating/

Have your clutch checked out by a local vacuum repair shop. That's a common problem with dyson brush rollers ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Brushes on hoover deluxe steam vac cvarpet cleaner are not rotating. Took out the brush assy and drive spins slowly but with little torque. Cannot seem to open the bottom to see if belt or direct drive..something wrong with drive mechanism for 5 brsuhes

(1) Assure the brush shut off lever on the hood is not set to the off position. \015\012(2) Is there still a square pin standing up from the one drive brush? It should be 1/4 square, and about two inches tall. That pin is the drive from the ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

Brushes are not spinning. think the belt is off or broken. how do i access the belt?

There is no belt in this machine. The brushes are turning by an air driven turbine. The turbine has a pivot bushing made of steel inside of it that gets rusty because of the water that is running through it. The turbine will have to be replaced an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this

... Vacuums

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Replace broken belt on a Hoover Elite Rewind. Removed bottom panel, how do I remove brush to put on new belt?

I have the agitator belt style 190 for the Hoover elite rewind I put it on and the belt broke again what do I do help carpet needs cleaning. ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks

If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?

Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

The vacuum sucks good, but the brush on the bottom wont turn, and the belt seems tight

Even tough the belt is intact it still might need to be replaced. Here is a replacement:Dyson DC14 Belt and Manual ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The brushes at the bottom wont spin round or pick anything up?? help

The belt needs to be changed. to replace the belt remove the screws on the bottom of the brush housing and you will see hte belt, make sure the spindles that the belt goes on are clean. ... Vacuums

My brush stopped spinning and there are no clogs and the belts are not broken any suggestions?

This depends on witch company vacuum you have\015\012you may have a switch or motor to drive the brush ... Vacuums

Hoover steam cleaner spin scrub brushes wont turn cant find belt

I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0814 seconds