Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

I HAD MY DC17 VAC FOR 3 YRS NOW NO PROBLEMS AT ALL, I REGULARLY CLEAN THE FILTER LIKE IT SAYS BUT LATELY I'VE NOTICE THAT THERE SEEMS TO BE A LOT MORE COLLECTION ON THE TOP OF THE FILTER WHEN I'M DONE VACUUMING. IT HAS ALSO STARTED THIS WEEK TO MAKE A VERY LOUD HUMMING TYPE NOISE WHILE RUNNING, I HAVE CHECKED FOR ALL POINTS FOR ANY BLOCK AND NOTHING AND NOW TODAY IT RUN A FEW MINUTES AND STOPS AUTOMATICALLY,IT WILL RESTART AFTER I LET IT SIT UNPLUGGED.WHATS UP WITH THIS THING, IT HAS BEEN GR


Answers :

The vac is over heating. First, you should try a new filter. Also, keep in mind that after cleaning the filter, make sure that it fully dries. Using a wet or damp filter clogs it quickly. Second, turn the vac upside down and make sure that the roller is fully cleaned and free of hairs and strings. Afterwards, with the vac upside down, quickly power on and make sure that the roller spins and listen carefully for noise at the roller. There may be something stuck inside. If it doesn't spin, verify that the belt has not slipped off or broken.\015\012
\015\012Good luck.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I HAD MY DC17 VAC FOR 3 YRS NOW NO PROBLEMS AT ALL, I REGULARLY CLEAN THE FILTER LIKE IT SAYS BUT LATELY I'VE NOTICE THAT THERE SEEMS TO BE A LOT MORE COLLECTION ON THE TOP OF THE FILTER WHEN I'M DONE VACUUMING. IT HAS ALSO STARTED THIS WEEK TO MAKE A VERY LOUD HUMMING TYPE NOISE WHILE RUNNING, I HAVE CHECKED FOR ALL POINTS FOR ANY BLOCK AND NOTHING AND NOW TODAY IT RUN A FEW MINUTES AND STOPS AUTOMATICALLY,IT WILL RESTART AFTER I LET IT SIT UNPLUGGED.WHATS UP WITH THIS THING, IT HAS BEEN GR


The vac is over heating. First, you should try a new filter. Also, keep in mind that after cleaning the filter, make sure that it fully dries. Using a wet or damp filter clogs it quickly. Second, turn the vac upside down and make sure that the roller ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC07 Yellow Vac, I use this vacuum professionally and clean it after every job so there is no issues with the filter which are replaced regularly. When you turn it on it makes a noise as if it were blocked....I have checked all pipes, hoses and now disassembled the machine to the point where the motor is out. I have found that a small rubber valve or bleed valve (Attached to the right hand detachable filter housing and activated via an internal spring) is popping when the vac


Hi, Where exactly is this spring? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

A h2oflo steam mop that will not steam. Have checked the spray device in water container, in filter area, and the point comes out to psh when the motor is running and switched on. What more can I do?


... Euro-Pro Deluxe Steam Mop S3202 Upright Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.


Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum

Replacing filter Got a Filter Queen Majestic vacuum from my inlaws when they moved overseas. I am in middle of vacuuming, got a weird noise, so opted to check and clean the filter for first time. UGH. The lower 'pot' that's the bottom part of the thing was full of gunk, but the filter pristine clean against the cone that's attached to the upper part of the unit. In other words, I am shocked to see that the dirt goes not INTO the filter, but outside of it into the bottom portion (that I call the


Its normal operation so don't worry ... Filter Queen Majestic Canister Vacuum

Noise Hi... I was doing normal house work and had been using it on carpet... I put it on floor for my hardwood floors and picked up loose clean cat litter and went to put it back on carpet and it made a horrible noise like it was rubbing. cleaned the filter... cleaned the roller thingi ...checked the belt and it is still making that horrible noise. It does not make the noise when I have it on floor but as soon as I put it on carpet it screams at me. Help! Please and thanks Linda


Hi Linda,\015\012Sounds like clutch problems, try to move the lever for carpet/floor back and forth a few times maybe it will free up. If it still makes the grinding noise, the clutch assembly will have to be replaced. Let me know, i can even ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos


It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Using my unit (owned about 6 years - great service so far) it suddenly quit ... no wind down or 'prelude' like whine - growl - etc. -- it just quit running ... suggestions? clear filters? done check power? how check power cord? done help ...


I agree with you having great service because mine only lasted two years. It sounds like the motor just worn out. If you don't smell any burnt electrical then replace the bushing for the motor. Good Luck ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.


I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore 21875 One day it's working fine. Next day, it won't turn on. When I attach the hose to another vacuum cleaner, it runs. Is there a reset button on the canister? Could it be the receptacle is bad? My Kenmore Progressive won't turn on today either -but was fine last week. I cleaned the filters checked for blocked air, tried a different outlet and no luck. I'll check the pins on the connections and see if one of them is not matching up or appears worn.


Give the prongs a wiggle and see if there is any play in them.Might just be a plug end. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I have a mile tt2000 that works fine up to 1300W but if I crank it up higher the motor decreases and increases speed every couple of seconds. I have changed the bag and filters and done the usual cheCks for blockages but can find nothing amiss. Unusually when it is running and I block the intake it will run at full power but as soon as I clear it the motor "hunts" again. Any ideas.


... Miele Cat & Dog 326i Bagged Canister Vacuum

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r


... Vacuums

Samsung sc8442 vacuum - has lost its suction and makes a meduim to high pitched humming noise if turn up above halfway on the suction. this also makes the red light come on. I've cleaned the filter and checked around a bit but cannot find out why it's doing it...?


There are several filters. when you take the dust box out, you need to clean this filter as wellhttp://www.4ourhouse.co.uk/cgi-bin/finder.pl?ftype=443401&brand_change=&section=0&path=&hb=0&brandset=9925&model=10689 ... Samsung Vacuums

Hi my dyson makes a really high pitched screeching noise when you first turn it on and also it is not picking up as good as it was. I have cleaned the filter and my husband has checked for blockages. It used to nearly **** up the carpet but now is struggles especially with the tools. I have had it for 3years. Thankyou


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a DC07 which is not picking up very well. I've cleaned the pre motor filter, was not aware of the post motor and will check. However, do the Dyson brush rollers wear to the point of not picking up things from carpet?


Hi The filter is only part of the cleaning process with a Dyson.\012\012I would suggest you get a 2 p peice and unscrew the plastic screws on the base. You will likely find that this area has clogged up. Clean this area out and put solepl ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Def no choked probs, as I check and clean filters regularly, but when switched on there seems to be a short whineing sound before returning to normal, and def wont lift fluff etc., just runs over it, although ther seems to be a fair amount of suction. It does clean but not properly


Hi, this is Jack at Dyson.\015\012\015\012You should be able to resolve your problem by following these simple steps: http://www.dy ... Dyson Ball DC24 Bagless Upright Vacuum

Shop vac shop-vac quit working while in operation and will not turn back on. No strange noise or anything beforehand. Filter had apparently fallen off at some point but on proper reassembly, still not working.


Could have a bad switch, bad cord, or a problem with the motor. ... Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.


Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums

Model #3760-2 Bissell upright vacuum- making very loud noise when running. Cleaned all filters- no difference


Is the noise coming from the belt area, ie. beater bar, or does it sound like it is coming from the motor itself? It is possible there is something caught in the brush roller.When you turn the roller off, does the noise go away? ... Bissell Vacuums

My savvy has lost suction. I checked for blockage in hose and is ok. The filter basket is clean. the motor runs strong. What else could it be?


Facing the back you will see 2 chanels one on the left where the hose comes out and one on the right that entends down into the base.start with the one on the left,its shaped like a j..there are 10 screws take those out and clean the chanel.be carefu ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

I bought a Hoover Wind Tunnel in January 2008. At first it worked great though very noisy. Now it will not pick up small fuzz on medium shag carpeting. I have checked the bag, the filter, the belt, and obstructions and there are none. Plus the noise level has increased. What is wrong? I am very dissatisfied.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=563001 Generic problem for all Vacuums I bought a Hoover Wind posted by smithcarolj1 on May 01, 2008 I bought a Hoover Wind Tunnel in January 2008. At first it wo ... Vacuums

Suction Problem I took my unit to my work and used it, when I returned home it wouldn't suck up anything. I took the recovery take out and it has inward suction. Shouldn't that be outward, so it goes into the tank? It also blows out of the bottom by the brushes. I check the filter in the bottom and that is fine. Is it possible that it is somehow reversed the direction of the air flow (rotor running backwards)? I am perplexed. What am I missing?


There is a stand pipe seal where the bucket sits on, and if it isn't there or out of place could cause a suction problem like you said yours is doing. In the picture it is #10. The motor seal may have gone bad and is leaking # 15.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a DC25 that will not pick anything up. It seems to be throwing everything back out somewhere. It only powers on when its not in the upright position. There is also a strange noise when it's turned on. I have taken the whole thing apart and cleaned all of the filters and checked for blockages but it hasn't help.


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC25. You should be able to resolve the issue by following these simple steps: ... Dyson DC25 All Floors Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0490 seconds