Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

My dyson DC17 animal has started to make an extremely loud noise after a rug got caught in the roller brush. What do I need to do to fix it?

Answers :

Probably a flat spot on the belt, replace the belt
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson DC17 animal has started to make an extremely loud noise after a rug got caught in the roller brush. What do I need to do to fix it?

Probably a flat spot on the belt, replace the belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I ran over a big floor rug with my vacuum and some of the strings from the rug got tangled in the roller on the vacuum. It makes a terribly loud noise even now after I have cleared the strings from the rollers. What else can I do to get rid of the loudness?

Loose area rugs should never be cleaned with any revolving brush vac. They will damage the rug by destroying the fringes and corners. In some cases the brush will also pull out tufted as the rug is made so poorly. Natural fiber rugs should never have ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Roller not turning when I drag vacuum across the rug. Got something caught in it, pulled it out, then stopped working properly.

Check the belt and what got stuck in it ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Throw rug got caught in rollers and now it wont pick mup were are belts located on hoover windtunnel dual 5

Nylon belt in center of brush underneath . not a hard belt change. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I got a shoelace caught in the roller brush on a vax upright pet and the brush has now stoped spinning. How do I fix this please?

Your gonna need to remove bottom plate and take a sharp knife or scissors and cut the string close to the brush then peal off. might need to replace belt at this time. just pull out brush roll and remove belt then match it up with new one and put it ... Vacuums

Belt needs fixed after sucking up a soft rug.

If its a canister model there probably is no belt just suction.open the canister and if it has a bag feel the bag ,if it feels kind of hard then the bag is full.take the tool off the end of the hose and turn it on to see if you have suction if you do ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?

The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Hei, I have sewing machine Brother NV500D and got technical problem need to be service/repair. I'm now in Malaysia and don't have techinical/repair service for sewing machine NV500D. This is overseas model. In sewing machine screen display 'F04'. The problem automatic needle not function and part missing. I dont no how to fix this. Can't i got the instruction manual service picture if i can't fix own. please help me. thank you.

... Vacuums

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.

This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together

Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Hello, I got a used Kirby Sentria. When I run the vaccum and push and pull on the handle, I can hearing a friction type noise. I got up close to the vaccum and it is not the wheels or roller. It is coming from the base of the handle. It's like it is pushing on something on the vaccum body and is creating the noise. Maybe transmission? Is this normal, or is it something I should be concerned about? Thanks for your help!

Try new belt yours may be slipping ... Kirby G5 Bagged Upright Vacuum

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.

Squealing ... Vacuums

Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser

That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it's generally not worth the time and money to replace.I suggest getting a different type of vacuum, maybe a Miele or Sebo. W ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Roller does not turn; I was vacuuming a rug and a string got stuck in roller-took it off but now the roller will not turn. suction is fine.

The roller drive belt may be stripped, worn partway through where it goes around the motor shaft, thrown off the motor shaft, or broken. Take the bottom plate off the carpet sweeper and have a look.If the belt was damaged when the roller ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Dyson 17 DC Animal - hit a nylon strap that got stuck in the roller. Removed strap but roller made noise when engaged, now roller not engaging but rolls free when turned manualy.

It could be the belt. Here is the replacement belt you need:Dyson DC17 Belt ... Vacuums

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt

... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

The roller-brush on my Dyson DC17 makes a terrible noise at all times. I removed the cover and extracted all debris from this area, making sure all connections were as secure as possible, but that didn't improve it any. The vacuum still seems to vacuum okay, but the noise sounds horrendous. How do I fix it?

Check the belt to see if a layer or piece of it has come loose and is flappping around.\015\012Check for any loose parts that could be getting hit by the brush or other moving parts.\015\012Make sure the brush it tightly in place and can ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a hoover savvy that the rollers wont turn. I've taken it apart to make sure the brushes are not caught but nothing happens. I only used this vacuum once. It was a floor model when purchased. I just need to figure out what I need to do to get this to work.

Hi there SmartAlec from NelsonVacuums.com.au here. I have to say that if it is not as simple as a belt - I assume that when you checked that the brushes weren't caught that ... Hoover U8125-900 Savvy Bagged Upright Vacuum

Hi guys, I have a bissell 9400 2x proheat with a fault. When you turn on the machine it trips the RCD in my house and makes a poping noise, i am a little technical so i had a look inside. The pcb under the handle was damaged with burn marks i unpluged this and tried again and the machine powered up, don't think the rollers moved though. What do i need to change roller motor,pcb?? Help please!! Regards Russ

I've seen the same problem in one of these we had in for repair. The pcb in the handle is involved with controlling the roller motor. The problem is with the motor. In my view, this machine is a triumph of design over practicality... The motor is loc ... Vacuums

Loud noise?? my vacuum suddenly just got really loud. it suctions fine, i changed the belt, but when the roller is off its not loud, but when i put it back on the 11noise is horrific. it vacuums fine i just cannot stand the noise. please help

I have the exact same problem. I've taken the thing apart and cannot figure out what is causing the noise. It's not the belt and it doesn't seem to be coming from the engine. It sounds like the spinning brush is hitting something, but it's not, th ... Bissell 6590 CleanView Bagless Upright Vacuum

Hoover nano cyclonic making a rattling noise after a shoestring got sucked into it and was removed. what to check to fix the rattling noise.

... Hoover Vacuums

Roller got power cord. This stretched out the belt. I replaced the belt, now the vacuum is making a noise. Cant find anything wrong, what could be making this noise?

Most rollers have several different positions you can install the brush in check and make sure the roller height is equal. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0719 seconds