Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


Answers :

There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your suction issue.
\015\012
\015\012c...
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My roller bar doesn't seem to be working, but I checked the belt and it appears to be fine, but a bit loose. Is this the problem? dial on front to determine heighth is also very loose and does not click anymore like it did a few months ago. Any help would be appreciated. thx.


If the brush roller stalls when it comes into contact withthe carpet, it might be that the tensioner spring has broken off. This is adesign flaw in the Eureka4870. The symptoms are: 1) brush spins until it contacts the carpet then itstalls, 2) the br ... Eureka Smartvac 4870 Bagged Upright Vacuum

Burned out The best way for me to describe the problem is to post reviews I made on Amazon.com, which is where I purchased them. ________________ Based on my past experience, I bought another 6 months ago. I live in a very tiny 2 room apartment and do not vacuum lots of dirt. I noticed this new vac getting very hot to the touch where the motor is located with only a few minutes of use. Today it just STOPPED. When I felt the canister, it was HOT. It obviously has burned out. Upon closer inspect


... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.


You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

I bought this dyson vacuum cleaner 10 months ago and the roller has not worked for the last two months. Can I return it for a new one?


The answer to this may depend on what country you live in. Within the first year (which yours is) you should be entitled to either free repair or replacement, provided the problem is not self-inflicted. If you live in a country that has a free Dyson ... Vacuums

My vacuum has suction with the long tube assembly but not any significant suction down by the rollers. I assume there is a clog or a problem between where the hose attaches to the machine and the rollers but I can't figure out where to look for it. HELP. I've only had this vacuum for a few months and I'm really dissapointed!


Go to the bottom of the machine and to the rhs of the rollers you can see the pipe - also remove hex panel on back and remove hose from elbow , i also found that a filter cx did wonders ... Miele S7210 Bagged Upright Vacuum

SEBO Sensors Where are the SEBO X4 sensors, I have taken this apart and not too sure where the sensors are. In particular I get Replace Roller coming up, but roller seems fine and it goes round ok if I disconnect the PCB. My unit turns on spins for 10 seconds and then brings on light C. Just replaced the motor on it about 4 months ago so not too keen to get a new one. Any help welcome.


... Sebo X4 Bagged Upright Vacuum

I HAVE A FANTOM VACUUM CLEANER MOD.#F1205400. I PURCHASED IT ABOUT 6 OR SO YEARS AGO.IT WORKS PERFECT,AS FAR AS SUCTION, THE ONLY PROBLEM IS ABOUT 2 MONTHS AGO,SOMETHING HAPPENED TO IT AND IT GOT VERY LOUD, KIND OF LIKE A CAR WITHOUT MUFFLER. I TOOK IT APART,AND FOUND NOTHING OBVIOUS. CAN YOU GIVE ME SOME IDEA OF WHAT I CAN CHECK TO RESOLVE THIS PROBLEM. AS I SAID BEFORE IT STILL VACUUMS GREAT. THANK YOU, VINCE


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums

I have had a Hoover Linx cordless stick vac for several months. Even after charging the battery the vacuum will not run at all. What are potentially the problems and how do I get it fixed.


... Hoover Platinum LiNX Cordless Stick Vacuum

I am hoping my Kirby Sentra has a reset button. It is only 5 months old and it will not turn on.It worked a couple hours ago. The vacuum will work with the hose attachment but not with the roller.


... Vacuums

My Hoover F5835900 will not **** up water out of my carpet! No problem putting the water down....just will not **** it back up. I bought the darn thing a month ago and have used it once.


Make sure the canister is inserted correctly and that the float that shuts it off when full is not stuck in the up position. ... Hoover F5835900 Upright Steam Vacuum

Not working We just bought our Dyson DC18 2 months ago, and today it lost suction. The motor will not come on. The roller thingy will, but not the motor.


If only 2 months old, take it for repair as it is under warranty. ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.


... Vacuums

Victa Vantage VCS464 148cc purchased 4 months ago. Problem - not starting. checked fuel levels, oil level and air filter. Leaking oil thru muffler when trying to start. Kevin - 0448594628 Melbourne.


... Vacuums

I have the Hoover Pet Cyclonic. I bought it new about 2 months ago. Now, suddenly, the roller won't turn. I took the cover off and ran it and the larger belt turns fine, but the vbelt won't engage at all.


... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I have an electrolux cyclone 1900 watt which has lost all of its suction, its not picking up properly...I only brought it 5 months ago but can't find the reciept...so am unable to get an exchange. I've tried to change the filer but the problem persists. Any suggestions?


It has to have a clog somewhere, either in the hose, or down by the brush roll, the dirt inlet may be clogged. But am sure you have warranty on it, contact the company or your salesman to see where you can take it for warrenty service. ... Vacuums

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?


Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums

There seems to be a short in the motor of a Miele S716 vac. Water was accidentally sucked up about 2 months ago


Are you sure about the model number, S716 doesn't come up. But it could be a bad motor, or it be a circuit board mounted by the motor. ... Miele Vacuums

No suction Own a Bissell Easy vac (bagless). Only just over a month old & it lost suction from the brush roller & hose. We've cleaned all filters & checked hose for clogging. Any recommendations?


Http://www.fixya.com/support/t1845597-debris_getting_stuck_in_vacuum_hose ... Black & Decker Vacuums

I am looking for a Hoover Steam Vac Bare Floor Attachment, Part #90001331. I found one in the US for $8.95 but by the time I paid shipping and handling it would cost $91.77, a little ridiculous. I am looking for one in Canada. Can you help. I have heard Hoover has been bought out and parts are very difficult to purchase. I bought this 1 month ago and I'm sorry I didn't know this prior to purchasing.


Hoover Bare Floor Attachment F5XXX from Usavacuum.comIt is $6.99 and shipping should cost you le ... Hoover F5906-900 Upright Steam Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

Power I bought my Vac about a year ago for a home project, used it about an hour total, and when i went to use it today, it started to turn on, and then shut off.  I thought i tripped a breaker, but that was not the problem.  Very confused. George


I had a similar problem with a Shop Vac. The solution was to disassemble the power switch and polish the metal electrical contacts to remove any oxidation caused from humidity. Tedious and time consuming but effective. ... Craftsman 17026 Wet/Dry Vacuum

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.


This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0462 seconds