Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

I have a blockage in the wand and don't know how to remove it. No suction

Answers :

Disassemble Your Dyson Animal so you can access the area around the wand. If the block is in the wand itself, you can clear it by passing something through it (such as a broom or mop handle).
\012Blocks in other piping and outlets can be removed by hand.
\012Beauty of the Dyson Animal line is that a homeowner can find and fix problems easily.
\012You can download the manual from here: http://www.manualowl.com/m/Dyson/DC17/Manual/205779
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a blockage in the wand and don't know how to remove it. No suction

Disassemble Your Dyson Animal so you can access the area around the wand. If the block is in the wand itself, you can clear it by passing something through it (such as a broom or mop handle).\012\012Blocks in other piping and outlets can be r ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.

Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s

I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.

Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

Dont know how to remove wand from the vacuum - Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have no suction for vacumming the floor. the wand is totally still working and sucking it heart out. clear hosing doesnt looked cracked. dont know where else to look.

Hi, if the wand is doing its job very well, you have to have a blockage some where, either in the hose where it attaches to the bottom of the unit near the roller section. It may be hard to see, but this is what is causing the bottom from not picking ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The wand appears blocked but there are no blockages, there is enough suction to collapse the wand but no suction

The filter at the bottom has been washed or not? ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The suction that comes out of the wand is very light, it's sucking things up, but the suction is very light. You know how you put your hand on the wand of a vacuum and the suction is so strong you

Check this video out ... Dyson DC25 All Floors Bagless Upright Vacuum

I need to know how to remove the dirt container on the eureka bagless vacuum. It says that it is easy to remove, yet we cant figure it out. is there some trick to it that we dont know?

There is a lever at the bottom of the dirt cup,turn it to the left and pull out the dirt cup.note while you have the dirt cup out make sure you clean all the filters there is one right above the dirt cup pull out on the right side and there is a filt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.

... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

The hose to my Dyson Dc24 has no suction. There is suction from the exhaust when I move the cyclone bin. I have removed, washed and replaced filters. The valve next to the top filter keeps flapping. I've checked for blockages and can't find anything.

... Dyson Ball DC24 Bagless Upright Vacuum

Plug Part # 8191782 on my kenmore vacumm wand is bad, I dont know how to get the wand apart to change it

... Kenmore Vacuums

Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.

You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

No suction when wand is used. Checked for all blockage. If you disconnect no suction at base

Hi there,Sorry to hear you're having difficulties with your DC24. Although I note you've already checked for blockages, you may wish to follow the steps shown in our support guide, to make sure you haven't missed anything: ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction i have been using mine for like a year or so. today i went to use it and then no suction. the water comes out but it wont **** it up. I haven't had any problems till now. I cleaned the little red filter but still nothing. I dont wanna take it apart with out knowing what im looking for.

I had exactly the same problem with my five-year old my Bissell 7920, and it's probably a broken pump belt.  See page 19 of your instruction manual for how to replace.  The Bissel ProHeat belt accessory pack costs $3.99 and you get a pump b ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it

Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum

My DC05 Dyson suction has stopped...there are no blockages, the seals are good, there seems to be more suction coming from a yellow box which is situated at the top of the removable cannister. There is nothing obvious'

My Dyson had exactly the same problem. I found the problem was caused by a blockage in the hose. Take the hose out where it joins the cleaner (it will come out if you pull it downwards gently) and take the hose out of the handle by squeezing the ye ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

There is no suction from the sweeper head but plenty from the wand. I have viewed several videos and visited seveal dyson web pages and none address this problem. I have thoroughly checked for blockage per video instructions. There were NO BLOCKAGES. Please help. Thanks Doug

Hi Doug,\015\012\015\012There are several things that this could be. Probably the most common problem that we see when customers come in with this problem is actually a fairly simple problem to fix. Here are just a few things that this co ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

NO SUCTION My Electrolux Z2274 upright vacuum cleaner has lost it's suction and is very noisy. Have checked and rechecked there is no blockage. Have cleaned the filters. In fact done everything I can think of. Any one know why and how to fix this??

If you have no suction, there are only a couple of things that could cause it. As you have checked for blockage, and changed your filters, you may have a vacuum motor with bad bearings, or broken fan blades (inside/on the vacuum motor). Either sympto ... Electrolux Central Vacuum

Motor sounds loud and high pitched. Suction seem ok, can't find any blockages. Cleaned filter at top of removable canister. Exhaust seems hot and low. Can there be a blockage within the motor housing?

Most likely your bearings are shot. it will need a new motor ... Kenmore Vacuums

No suction hello, there was a rubber smell then no suction. i'm thinking it needs a new belt but don't know how to remove the cover to replace. is it a complicated procedure. is there a diagram available? don't have any info here. thanks, leslie

Flip the machine upside down and remove the four screws from the baseplate. Replacement should be fairly self-explanatory from there. If it's a self-propel model, note that the v-belt in the front WILL look loose normally, so it does not usually requ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.

Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum

The wand on my DC07 Vacuum has no suction. I have taken aprat and can not find a blockage

... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0515 seconds