Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

I ran over a shoe lace and the brush on my dyson quit rotating how do i get it going again?

Answers :

Turn it off and turn it back on again and it should reset.If that dosent work you probably broke the belt.It's easy enough to replace by just removing the bottom plate and the brush and installing the new belt. www.sewvac.com
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I ran over a shoe lace and the brush on my dyson quit rotating how do i get it going again?

Turn it off and turn it back on again and it should reset.If that dosent work you probably broke the belt.It's easy enough to replace by just removing the bottom plate and the brush and installing the new belt. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab

(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

How do you get the beater brush to start rotating, the dyson was just cleaned and the beater brush won't rotate

Sounds like the rubber drive band has not been replaced properly to drive the brush and/or the brush was not properly cleaned.\015\012You can find the manual here:\015\012\015\012http://dl.owneriq.net/4/4d79dca8-65d8-4c46-a58a-a2fef1f89635.pdf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Ran across shoe lace and when I pulled it out the beater bar quit rotating

Just cut the sholace part that you can see... it will get it into a lot of small peices and just pull out the smaler laces ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

We are on our 3rd Dyson. Both times we have replaced them it's because the rotating brush quits working after retreiving a string (or tie from an article of clothing) from the brush. Is there a fix for this? I'm stuck with the same problem at the moment and really don't want to have to return this 3rd vac!

It could be the clutch, cheap and easy to replace.But it could also be the brush control knob is turned off.If you visit\015\012http://www.sparesaver.com/help-and-support/dyson-section/dyson-technical-advice-450/\015\012they h ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I caught a shoe lace in my Dyson DC17; pulled it free, opened the brush/roller area and cleaned everything but the brush still won't work. Read somewhere that there is re-set button but the only one I found was to switch between the brush / sweep functions. Is there a fuse / connection / part that may need to be replaced?

I don't believe so. Keep trying the reset button. Sometimes the reset sticks. Hope this helps. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC28 works fine for a minute then it's like if the brush head gets too much resistance it quits spinning and the light starts flashing. When I turn the vacumn off then back on it's f

Hi Gayle,I'm sorry to hear you're having difficulties with your DC28. From what you've described, it sounds as if you may have the brushbar set at a level too low for the type of carpeting you're cleaning. If you select a higher carpet settin ... Dyson DC28 Animal Bagless Upright Vacuum

The rotating brush on my Dyson DC25 wont go round - can you help - the machine is new but I don't have the manual?

... Dyson DC25 All Floors Bagless Upright Vacuum

Bissell Lift OfF Brush Roller Stops Rotating

They make the worst machines, the rollers are cheap and they make it so you cant take them apart to clean them. You don't want a dyson either, they aren't any better for pets. With all that hardwood floors you should get a good canister vacuum, sebo ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Caught shoe string in roller brush, now will not rotate roller BR

Belt maybe streched and hardened from heat replace and try again. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.

If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look

... Kenmore Vacuums

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!

Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx

Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My FEIN 9-55-'13 recently started making more noise and is now officially a "screamer". There also developed quite a vibration associated with the noise which made me think it was probably bearings. So I took it apart and found no detectable play or lateral movement in the bearings, they seem fine to me. So I thought perhaps the brushes. The rotor where the brushes ride is quite black but I can't figure out how to get to those brushes, although I don't really think they are causing the noise

This problem is only caused by one thing the motor bearings are noisy, I have never found any other reason, they may look good and fell good but trust me replace the motor and the noise ... Fein 9-55-13 Turbo II Bagged Canister Vacuum

Rotating brush Hello, my kenmore rotating brush is not spinning at all, and its causing the motor to cut the belt. should i get a new brush? Thank you.

Sounds like the brush roll has an end that is melted or frozen up so it won't move, in which case you need to replace it. ... Vacuums

The brush bar quit going around

Did the belt break? ... Vacuums

Dyson DC22 brush wont spin, does not appear to be getting power

Hi there,I'm sorry to hear you're having difficulties with your DC22. If you've been unable to get the Motorhead working after cleaning it, please get in touch with us directly so we can provide further assistance. You can call us free on 1-8 ... Dyson DC22 Motorhead Canister Vacuum Bagless Cyclonic Vacuum

Roomba. Diagnostic The brushes will not rotate. I have cleaned them, used an air compressor, and checked the front wheel. What can I do to get the brushes rotating?

Go to homesupport.irobot.com and get contact for help.and get the parts too.God bless you ... iRobot Roomba 560 Robotic Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1136 seconds