Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes

Answers :

Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.
\015\012An instruction video for replacing the belt can be found on the below link.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes

Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand

In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Light burned out and at same time sucking motor stopped working. Brushs still turns. is there as fuse I can change out or is the motor toast ? this unit is less then a year old

Contact your local warranty center they have had problems with that model ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Caught rug, motor overheated, the brush wont turn at all, but suction is still there ...is there something I can do to reset it?

Assume that the belt is broken to the power brush /head. Did you happen to smell burning rubber at all when the motor got stuck? The motor may have a reset on it, if it was not operating, but that is not the case, as mentioned. Look in your manual fo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush stopped spinning from fabric being sucked into it, how can I fix it? It's a Dyson animal vacum. The belt is not moving from the lower motor.

Turn upsidedown.\015\012There should be 3 plastic screws in a triangle shape.\015\012Loosen, but do not attempt to remove the screws.\015\012This will release a shield that will expose the brushes.\015\012Carefully remove the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles

Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

A large screw got sucked up the vacuum. Since then the motor,which I replaced probably only 12 months ago, sounds very "winey" and when you stand the dyson upright the front brush still keeps going round instead of stopping. Any ideas? David

Sounds like the clutch mechanism has somehow been damaged.\015\012\015\012Have a look at the following site which is a great source of info on faults, dismantling, repairing and re-assembling:\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc04 wont pick up,motor working,replaced clutch assembly but still dosnt turn brushes

You need to go through a process of elimination. You are better doing that here: Dyson advice forums ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Motor doesn't run I believe it the brush on the motor. two motor brushes one is completly gone about 1/8 inch left could this be the problem.the other motor brush still has 1/2 inch left. and current to motor tested good.

Sounds like your belt slipped off. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hello can you help me please? I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well? Can you help please? Thankyou Martin

Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor. ... Kirby G4 Bagged Upright Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.

I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.

... Vacuums

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

The Brush Motor on my Bissell Healthyhome Vacuum wont start

I had this same problem. There is a screw that holds the top handle and the lower handle "together". If this screw is not TOTALLY tightly screwed in, this will cause the contacts in the switch to BREAK contact, and therefore one or BOTH motors may no ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up

Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums

Vacume. motor wont spin

Most likely the carbon brushes are burnt out and need replacing. However - I wish I knew how to put this politely - if you don't know enough about electric motors to have checked for this already, you may not know enough to do the job safely yourself ... Vacuums

Flames and fine carbon particles came out of my Dydon DC29 which also partly melted the bottom filter. The motor is still working tho. I feel that the brushes are gone. How to get to the motor and where to get new brushes???

Hi Joel,I'm sorry to hear about your experience with your DC29. We'd appreciate the opportunity to provide further assistance, so if possible, please call us on 1800 239 766. Alternatively, if you email your contact details to us at ... Dyson Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?

Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The brush on my bissell helix (model 22C1-2) stopped working all of a sudden today. The hose still sucks and everything. I even cleaned the spinning brush and it still doesnt work. I just bought it in August.

... Vacuums

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano

... Electrolux Vacuums

When i start the vacum the brushes trun for about 3-5 seconds then stops. the vacum still runs,its just the brushes stop turning, what should i do?

If your machine has no power or interrupted power, please check the following:\012 \012- Make sure the power cord is plugged into a functioning outlet to check for power.- The handle may not be installed properly, causing a ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?

Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.

First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.2326 seconds