Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?
Need help to replace main motor on my dyson d17 vac
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Need help to replace main motor on my dyson d17 vac
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?
Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!
Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out
Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
I think I need to replace the main battery in my small floor vac - the one that can be hand held like a dust buster or work like a small floor vac. I need to know how to remove the battery and replace it with what kind of new battery..
I see my sense of humor is not appreciated...it was only a joke. Anyway, here is what you do: First, slide the battery cover off the bottom of the hand held unit. Remove the battery from the motor housing by pressing the tab on connector “A&rdq ... Vacuums
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum
Hi I need help because I have a problem with my Electrolux Centralux Central Vac system in my house. When I plug the vac hose in the central vac socket at first I heard the motor running very gently with NO suction then after a minute or so it went completely dead and they is NO motor sound, suction, or anything happening what so ever. Can anyone tell me what this problem is???
Have you checked for a clog in the lines or in the hose? If there is no clog in the system anywhere, then your motor could be dying. ... Electrolux Centralux Vacuum
Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.
You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums
I need a replacement manual for my Dyson 14. I have lost the booket and need help in replacing, removing, washing the yellow plastic filter
The information you need is in the manual. You can get a downloadable one here:\015\012\015\012http://homeappliance.manualsonlin ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?
Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum
Pls Help! My Dyson DC05 (Yellow) needs a new wand. Am unsure whether it is the assembly wand or hand one found in spare parts. The wand I need to replace connects the two long hoses together, and NOT the wand which fits onto pickup head. M.thks if you can advise which one I need. Getty rather dusty in my pad!!
... Dyson DC05 Bagless Canister Cyclonic Vacuum
Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.
My Air Vac is 20-21 years old. Recently it stopped running. I found the fuse by the motor was blown and replaced it. It blew immedicately when I turned it on. I think I need to repace the motor. Do you agree and can I buy a motor from you.?
If the fuse does keep blowing yes you do need to replace the motor. I am sorry we do not sell parts though. Try the link below to get the motor.\015\012\015\012 ... M&S Systems Vacuums
Unable to find a panasonic replacement motor for dyson dc07 vac.
You can convert it to the YDK one if you get the YDK motor housing as well. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
Kenmore 116.2481190 vac I need help with replacing the hose
... Kenmore 22812 Bagged Canister Vacuum
Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please
How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP
Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum
I need please a belt for the brushes the larger one but may be better to replace the smaller one as well. I can see how to replace the small one very easily but not sure how to get the new one onto the end of the big sprocket. Please can you help I have the vac disassembled ok just waiting to get the belt to reassemble it. thank you Colin White SEBO AUTOMATIX X1
As you know, there are two belts - the pulley device between the motor and the brush roller is the sensor that measures the drag on the brushes and operates the automatic height adjuster to maintain constant drag. To the left of that double pul ... Sebo Automatic X1 Bagged Upright Vacuum
I have a Dyson DC07 Yellow Vac, I use this vacuum professionally and clean it after every job so there is no issues with the filter which are replaced regularly. When you turn it on it makes a noise as if it were blocked....I have checked all pipes, hoses and now disassembled the machine to the point where the motor is out. I have found that a small rubber valve or bleed valve (Attached to the right hand detachable filter housing and activated via an internal spring) is popping when the vac
Hi, Where exactly is this spring? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
DYSON DC07 ANIMAL VAC: IT SHUTS OFF INTERMITTENTLY, GETTING WORSE SURE ITS AN OVERLOAD PROTECTOR IN MOTOR. HAVE THOROUGHLY CLEANED THE UNIT TO NO AVAIL. HELP ???
The circuit tracks should be getting cut somewhere in between some where so it leeds to this problem. ... Vacuums
How to replace dyson dc17 post motor filter (not the main "washable" one under the canister).
You do not have to disassemble the vacuum to get to the post motor filter. The above person does not know the DC17 if they are telling you this.\015\012\015\012You simply remove one Phillips head screw, it is Phillips because most consumers w ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My BROAN CV-110 hose with the rug beater only works if I turn it on from the base unit. Shouldn't it turn on when I plug the hose into the wall recepticle? Do I need to replace the hardware at the end of this hose and if so, where would I purchase that? This central vac came in a house I just purchased. Thanks for any help. Sherry
... Broan-NuTone CV450 Central Bagged Central System Vacuum
How to assemble motor housing on a dyson dc17. took it apart to clean and not sure how to put back correctly. need a diagram. please help!
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!
Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums
Dyson dc03 faulty cable The cable from the mains plug to the on/off switch has split and needs to be replaced. How do I gain acess to the switch ? I am a competent engineer but I do not wish to damage the switch/cover to repair/replace acble.
I've never worked on a DC3, but whilst the shape and position of the switches changes from model to model, most are secured the same way.\015\012\015\012If you look closely at the switch cover (the bit you press for on/off), there is usua ... Vacuums