Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

Make a very loud noise when I try to vaccuum the carpet. It sounds like it's something in the brush up front. Belts look good and obstructions are gone. Not sure what else to do.

Answers :

  • Try to lower your wheels a bit which will raise your vacuum a little off the ground. When you vacuum a bare floor you want the vacuum as close to the floor as possible. When you vacuum a carpet if you don't raise it a bit then the brush will grab far to hard on the carpet ripping the carpet up and possibly burning the motor up. Try raising the vacuum a bit, or a lot, and this should fix your problem.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Make a very loud noise when I try to vaccuum the carpet. It sounds like it's something in the brush up front. Belts look good and obstructions are gone. Not sure what else to do.

\015\012Try to lower your wheels a bit which will raise your vacuum a little off the ground. When you vacuum a bare floor you want the vacuum as close to the floor as possible. When you vacuum a carpet if you don't r ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Electrolux Epic 6500 SR Carpet Sweeper won't go on. Belt good brush moves, bulb looks good, reset red button I'm not sure, works, looks good. Vacuum starts has suction ,

This link is the manualhttp://www.totalvac.com/manuals/electrolux_manual_Epic6500.pdf ... Vacuums

Dyson hi my dyson sounds as if something is catching when the brush goes round, it's very loud, it still has good suction. I have taken the plate of can't see anything or fell if there is anything obstructing the brush, could it be the belt?

Hi.\015\012If the brush turns freely then you will need A new clutch unit fitted to your machine.\015\012There are loads of them on Ebay very reasonabley priced only buy new not second hand.\015\012\015\012Manuals are availabl ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

There is a high pitches nosie coming from my dyson. It mainly happens when the flooring type changes whilst hoovering. Everything else is ok. It sounds to me like the drive belt for the brush bar or could it be the clutch. Hoover is over 10yrs old but is in good order and well looked after, this is really the first thing that has ever gone wrong with it.

... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?

Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks

CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.

... Electrolux Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

My vacuum's rug brush will not spin. the belts are fine and in place, but when i engage the carpet brush nothing happens. i looked under the bottom and there are no obstructions preventing the brush from opporating/

Have your clutch checked out by a local vacuum repair shop. That's a common problem with dyson brush rollers ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have removed the obstructions in the brush bar and the brushes still will not rotate. What else can I check?

Hi Genie, it's Jack at Dyson.Once you've cleared any obstructions from around the brush bar and inside the cleaner head, you need to reset the machine. This is easy to do - just press the button in the red recess on the side of the cleaner he ... Dyson Ball DC24 Bagless Upright Vacuum

We have the GE sensor microwave WES1358DN1WW. It was made in 5/2009 & bought in July of 2010 brand new. it worked perfect til last week. i put something in it & it started to make a loud humming/vibrating noise. i assumed it was just something ontop of the microwaved & ignored it. 1 min later my food was still ice cold. we tried unplugging & plugging back in & made sure that it was clear of anything but it still makes noise & doesn't heat. GE charges $79 to look at it, & since the microwa

... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

The motor driving the brushes does not start or function in any way. It has been thoroughly cleaned and the bearings look good and the brushes rotate freely when the mach is off.

There are two conditions that cause the brushes not to spin. One ia a cold solder joint on the paddle board connector of the Cleaning Head Assembly and the other end that connects to the brush motor may also suffer From the same condition. Here ... iRobot Roomba 530 Robotic Vacuum

When I flip the switch on my sebo x1 upright, a red light comes to the brush and bag icons. However, I cleaned out the hose and checked to make sure there is no obstruction from the brush to the hose also, or from the hose to the bag. It is clear that juice is coming to the vacuum, but there is no sign of life except the two red lights.

Thanks for contacting fixya. You should pull out the bag and reset the machine. You should take all the user replaceable items. And turn it on. You will get lot of errors. Then turn the machine off. Put back all the accessor ... Sebo Automatic X1 Bagged Upright Vacuum

Hoover canister vacuum (windtunnel)- turned it on and it had good suction, then smoke came out and it smells like something is burning. Is it the motor burning up or something else?

Probably the belt..\015\012Turn it over so the bottom is facing up..\015\012Remove the plate that surounds the brush..\015\012Check to se if brush is spinning frely and that the belt is on there poroper ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

My Oreck XL upright is blowing out instead of sucking in. I changed the bag and cleaned the brushes; I also cleaned out the main "pipe." I looked for a place to change settings and couldn't find any, so I know I didn't inadvertently switch something. The brushes seem to be spinning at the correct speed. Thank you, Julia Byrem

... Oreck XL2200 Bagged Upright Vacuum

Brushes can some one please help me with my steam cleaner I have never used it myself but someone else did and Im not sure how to turn the brushs on .....i have never used it

Sounds like the belt is broken or at least the brushes are bound up with carpet fibers. Take a look and see which it is. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum


If reset switch is worn out, how does the unit come apart to replace it? ... Electrolux Vacuums

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!

... Roomba Robotic Floor Bagless Vacuum

My husband go the brush tangled in something. We cleared all of the obstructing string from the carpet fringe and the brush is moving freely but it still is making this awful noise when I try to use it like it did when it was tangled up. Is there anything I can do to fix it or do I need to find a repair person?

Probably your belt have a spot where i wored out when it got tangled up inspect the belt first ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My roomba keeps telling me "error and to clean the brushes. I have cleaned the brushes and when I turn the roomba back on it keeps clicking underneath the roomba. I'm not sure what else to do.

I had the identical problem. I cleaned the brush but the problem persisted. I then put in a new brush that was provided in the box and the problem vanished. I have since used the cleaning tool on the old brush and will try and reinstall it to see ... iRobot 4150 Roomba Vacuum

I have a hoover steamvac model # F5915-900 and the brushes are not turning when I turn the selector from off to low or high. I've checked to make sure the brushes are locked in place and they turn manually with no resistance. What else can i do?

(1) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(2) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches lo ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0891 seconds