Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

I have a dyson dc17 animal. When you put the handle down, it is very loud


Answers :

Hi there,

When you lower your DC17's handle into the vacuuming position, a second motor which powers the brushbar will switch on, which will make the machine sound a little louder than when it's standing upright.

However, if you're concerned that the noise the cleaner is making is unusually loud, I'd encourage you to get in touch with us directly - we'll be able to run through some troubleshooting checks over the phone to help resolve this.

You can reach us on 1-866-693-9766 - or if you email your contact details to [email protected], someone will be in touch as soon as possible to provide assistance.

Best wishes,

Jack
Dyson Online Customer Support
http://www.dyson.com
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor loud I have a dyson dc17..recently when i turned it on and pulled the handle down to vacuum the motor was very loud..put the handle in the upright position it is quiet.any suggestions?


When you put the handle down it turns on the brush roll. you may need to clean the brush roll or replce it if the bearings are bad.also clutch and 2 belts are started when putting handle down for brush operation. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc17 animal. When you put the handle down, it is very loud


Hi there,When you lower your DC17's handle into the vacuuming position, a second motor which powers the brushbar will switch on, which will make the machine sound a little louder than when it's standing upright.However, if you're conc ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson DC17 makes a loud noise when i tip the handle down to make the brush spin on the floor?


Loud noises are usually caused by worn belts, unbalanced roller brush or debris in the roller brush. Check these things. Here is a link to the belt you need: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson dc17 vacuum handle won't recline. - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


The under carriage is misaligned itself or has broken. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson sucks good untill i put handle down


Try moving the floor/carpet selector dial on base of vac back and forth, from floor to carpet repeatedly, at least 5-6 times....it may be stuck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cannot put handle on dyson - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi,Did you receive the handle with the wand already attached? It should be. Then, to get it into the hose pres the wand release button on the end of the hose and slide the wand into the hose. The wand should then be pushed into the slot o ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson dc17 hose will not come out/ handle wont release from machine. i've pulled the metal rod up all the way and the handle still won't come away from the machine so i can't use the hose and attachments. anyone know what the problem might be?


Hi there, it is possible that you have a blockage in the wand/hose assembly which is making this difficult to remove. If you are able to remove it to check for this, please contact our Helpline on 1866MYDYSON so that one of our advisors c ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson ball DC24 when you put the handle in the tube the handle goes toofar and pushes the bottom open


Hi there,I can confirm that what you've noticed is part of the valve mechanism, which switches the airflow from the hose to the cleaner head when you replace the wand on the machine. This is a normal feature of the DC24, and nothing to worry ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson makes a loud noise when I vacuum - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


You need to replace the belt. Here is the belt you need and a manual you can view which has instructions:Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I removed the handle of my Dyson DC24 to vaccum in high areas and now when i try to put the back piece back, it doesn't click. So when try to vaccum on the floor the handle just comes off.


Hi there,I'm sorry to hear you're having difficulty with your DC24. The wand handle should reattach easily to the machine, locking into place with an audible 'click'. If it doesn't seem to be doing this, you may want to check you have the han ... Dyson Ball DC24 Bagless Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

Dyson DC17 Animal does not have enough suction from the wand handle to power the mini turbine head. The wand handle has very little suction.


My dyson doesn't have suction either and nothing is blocked. In fact is was working great the vac that is, but when I used the wand for the first time to get the corners the vac shut off, I checked the hoses, filters and all nothing is blocked. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson is making a loud scweeky noise - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Www.sewvac.com Remove the bottom plate and disconnect the belt.If it still makes the noise it is the lower motor that drives the brush that is bad.If it dosent make the noise try cle ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson hose sucks good but, when i put handle down, it won't **** but brush does turn


I just had the same problem....suction from wand, but no suction from soleplate, the brush bar spins. Did all the troubleshooting steps on dyson.com but they didn't work...dyson.com says need to take to repairman, being a diyer I went to search engi ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Putting together the dyson DC25 all floors handle that regulates the switches


... Dyson DC25 All Floors Bagless Upright Vacuum

My dyson dc17 animal will pick up via the hose attachment but there is no suction when you use the regular vaccuum on the floor - you can hear the difference in the suction once you put the floor part down - we took it apart - cleaned it - checked all hoses - still does not work????


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC17. Everthing appears to be working but when I set it in motion I hear a loud screeching sound. Sounds like a belt on the brush roll cover but the roller still spins.


The belt might be worn and causing the sound. Here is the belt you need and the manual:Dyson DC17 Belt and Manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson DC17 will not turn on unless the handle is pulled back.(into the vacuuming position) The attachment hose will not work at all (0 suction thru it). I've checked the hose and made sure there is no obstruction. Any ideas?


Not sure if I can help, but I'll try. The DC17 has two motors: the vacuum motor and a separate motor for the brush bar. It is normal that the brush motor works only when the handle is pulled back in the vacuuming position - that's the way it's made. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Loud whining noise when in use - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


Hi there its Darran at Dyson here. Sorry to hear of the problem with your DC17. It is possible that there is a blockage somewhere in the machine which is causing the noise. To check this, please visit our website at www.dyson ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Loud grating/rattling noise comming from dyson dc04 when ever hovering upright as soon as i angle back the handle to push it. the belt has not come off, the roller is rolling and not jammed. sucks ok from the flexible hose.


... Dyson Vacuums

My dyson DC17 animal has started to make an extremely loud noise after a rug got caught in the roller brush. What do I need to do to fix it?


Probably a flat spot on the belt, replace the belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Model U57809RM Hoover Cyclonic which started making a very loud noise. Changed both belts on it but the noise persists. It seems to happen when I put the handle in the 'engage to vacuum' mode. The minute I start to lower it the noise begins. Help!


Hello,You could have a broken fan in the motor and need to replace the fan. If the noise is coming from the brush area of the vacuum, you probably have a broken bearing in your brush roller and would need to replace the brush itself. ... Hoover Vacuums

I have a dyson dc17,when i turn on the roller brushes it is very loud


... Vacuums

How to assemble motor housing on a dyson dc17. took it apart to clean and not sure how to put back correctly. need a diagram. please help!


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC17 Animal Bagless Upright does not click to stay in an upright position. It works but the handle falls to the floor.


This is a common fault with the Dyson DC07 (and other Dysons) unfortunately the clip that holds the handle upright hs broken. It can be repaired, but will cost a reasonable amount to have done... I would just live with the problem and prop the vacuum ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2225 seconds