Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

The little gear on the end of the brush bar motor is worn out. Where can I find a replacement gear?

Answers :

Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The little gear on the end of the brush bar motor is worn out. Where can I find a replacement gear?

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No power when turned on, I checked motor brushes and they are almost worn out, could this be the problem? and where do I find replacement brushes? I have checked on Dirtdevil's site but I don't see any motor brushes. I am in Montreal, Canada. Thank You.

Hi,\015\012Before that I wouild check the switch...the switches on those things go bad regularly...get a meter and check the power on either side of the main switch and I think your problem will be there...\015\012\015\012heatman101 ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers

The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

I need to replace the brush motor on my Bissell 9400...I can't figure out how to remove the existing motor. Took the clip off but can't get the gear off the shaft and the hole in the side isn't large enough to push the gear through...what's the secret?

... Vacuums

I have a dyson dc14 how do i repair my vacum? i need to try to replace the brush bar motor or something so that i can get the brush bar to work again.i hope you can help me out

Brushbar not spinning:--\015\012Ensure brush control is set on carpets mode. Note: brushbar will only spin when\015\012the handle is reclined.\015\012To get user manual for your vacuum please click on the link mentioned below\015\012 ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Carbon brushes on ME-48 power head motor worn out. Where can I get replacement brushes? Motor is O 90197X7, Lamb, Model 118173-73 - 240V 50/60Hz

Hi Les,Most sites sell only the motor.Here's a website that includes motor brushes: http://www.kleen-ritecorp.com/search.aspx?IsSubmit=true&searchTerm=lamb+motor&gclid=CIbZ59zwiKgCFQprKgod8W2itQHope you can find the righ ... Filter Queen Vacuums

I have a Germ Guardian GGU350TT. The Beater Bar Brush is seized up on the ends and no longer rotates. Can it be fixed or can I buy a replacement Beater Bar Brush? I've called the company and they were no help.

... Germ Guardian GGU300 Bagless Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I need replacement carbon brushes for the motor. I haven't been able to find a source.

Try looking for a power tool repair shop, they usually have some brushes and can order more. I have put Hoover brushes in my Shop-Vac.\015\012 Look for some that are close to matching,( spring size,spring length, brush length). If the brushe ... Hoover Portapower C2094 Bagged Canister Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Need to replace motor brushes on Kenmore canister vacuum 116.25914503 - Getting lots of arcing at brush ends. Need tear-down steps to get at the brushes.

If you can see the arcing you are likely in the motor housing. The brushes are specific to the motor depending on RPM. Most brushes and motors in Sears units are supplied by AMTEK Lamb. The color on the plastic housing and stamped model # on motor w ... Vacuums

I think the carbon brushes for the motor on my DC14 (animal I think)are worn out. Have you got instructions on how to replace these brushes please? Thanks

Here are useful sites for DC14 maintenance (plus DC07 which is similar)http://www.sparesaver.com/vacuum-spares/help-and-support/dyson-section/dyson-technical-advice-450/dyson-dc14-technical-advice-474/http://www.espares.co.uk ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike

... Hoover Vacuums

Have an e-series rainbow. Belt and brush bar have been replaced in power head. But the red reset button can still be pushed and it is not staying going like it should. May it be the motor?

... Rainbow E series Canister Wet/Dry Vacuum

About 5 years old... motor started a loud whine (with or without rotart brush bar engaged). doesn't appear to be any blockage that I could find.

Sounds like the bearings in the motor need greased or they are worn out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Spin brush will not spin. local repair man said one gear stripped and motor would need replacement. is this correct??

There is a plastic rod that sticks out of the back of the spin brush, this makes all of the brushes rotate. The motor would need to be replaced if it was not turning on anymore. this doesn't sound right...?I think it is just a broken pi ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

How to replace brush bar motor on dyson dc15 - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I am trying to replace the brushbelt. I have the brush off not surewhich end goes where. also I had it on once but the belt was off when it was supposed to on. I cant find my instructions ! help

I am going Kirby "G" crazy.\015\012I hope this URL will be of help to you:\015\012\015\012http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039\015\012\015\012If it is of help, please rat ... Kirby Ultimate G Bagged Upright Vacuum

The head on my canister vac vibrates, smells and makes a bad sound. When I took it apart the inside of the "end brush tufted" piece had bits of the plastic broken off. Should I replace the Agitator Unit Assy or could this be the motor?

If you are talking about the end cap is broken off the agitator, I would replace the agitator. you can check the motor by turning on the vac without the roller installed. ... Vacuums

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.

It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

The plastic drive unit were the brushes attach have two of the four plstic ribs broken, this is the one located on the end of the motor, I will to replace

Electrolux Floor Pro shampooer and polisher (Aerus)\015\012\015\012I'm not sure what your question is, but you'll probably need to take this to an Aerus Electrolux store for repair. They may not have the parts on hand, but can order them ... Electrolux Floor Pro Vacuum

I have a InStyler (the rotating iron) by Tre Milano. This device is for styling hair. This is not a flat iron, but a cylinder that warms up and rotate's against a brush. It has 3 heat settings which works fine. Problem is cylinder has stopped rotating. My husband disassembled and believes the motor for the rotation has worn out? This is the question he had and mine is can it be replaced ? I have model number. . IS-1001 120v 60hz 135w. Conforms to UL STD. 89 0927-037875. Also stamped on the small

I'm repairing an Instyler right now. \012Troubleshooting, I connected a multimeter and measure the voltage where the motor is connected. When I push the button that makes spin it, I measure 12Vdc which is a correct value for that motor. Then I co ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1125 seconds