Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

Debris around the motor shaft

\015 I often have had to clean the "gunk" around the motor shaft where the belt fastens. There are times that the debris will get under the belt on the beater bar and actually cause the belt to rub on the sole plate.\015

Answers :

Remove sole plate then you can get to the belt
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Debris around the motor shaft

Remove sole plate then you can get to the belt ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Rick E1, it looks like the Motor Pulley, Elna #440152-20 needs to be replaced on my 722010 model (flat on one side from standing around. It looks like some kind of a set screw which keeps it attached but are you familiar with how to get this item off the little shaft it is on. Also, any idea where I could find a reasonably priced Motor Pulley.

... Vacuums

Problem getting belt around motor shaft... Eureka The BOSS

Make sure the vacuum is in the upright (locked position) - when you lower the handle, this puts tention on the belt. If it is in the upright and locked position, there is plenty of clearance (unless you have the wrong belt. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Can't figure out how to get the belt around vacuum motor shaft

I am assuming you are referring to the beater bar belt. You will either find a release lever on each side or a small screw and bar restraining the bearing that holds the bar in place. Removing whichever of these you find will allow you to install t ... Eureka Smartvac 4870 Bagged Upright Vacuum

No power I ran over an elastic hair band with the hose that wrapped around the shaft (not the brush). Since then, no power. could the motor have burned up?

If pieces wrapped around the fan fins and jammed the fan from turning, this could be the problem. You may have to remove the front of the vac to get to the fan. ... Kirby G5 Bagged Upright Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Vacuum motor shaft too hot

Check the brush roll ends, will they turn easily or is one frozen. If so, you need to replace the brush roll. If the motor turns on, it and the belt are trying to turn the brush roll and can't. Also check the ends where the brush roll sits in and ... Dirt Devil Featherlight Bagless Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse

By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti

You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

Bissle vacume can not fit belt around motor

It sounds like you got a belt that was too small, if it is the right belt it will be hard to get on. But once its on you will be all set. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Replacing belt but where is the motor shaft

The shaft of the motor might be through the hosing on the under side of the vac where the brush is. give me the model # ... Hoover U6476-900 WindTunnel Vacuum

Bissell bagless motor shaft is too hot and melting belts

My guess is that the roller binds on the carpet (high pile?) and the motor shaft, glazed from use, spins without moving the belt and quickly burns a hote through it. I've had that experience! ... Bissell Vacuums

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??

... Kirby Vacuums

The motor in my Powermate (Kenmore Canister 116.27614700) is whining, high pitched, but still works. A local shop told me the motor is dying (the one in the Powermate that drives the beater bar) and would cost $150 for them to repair. The machine is only 1.5 years old and I paid $300...yikes. I think I can fix it but don't understand why the foam gasket that apparently wraps around the motor costs as much as the motor. This is assuming that part 32 (ks747156) is the foam I see glued to my cur

I think you are right! Buy the motor.....use the gasket from the old motor if you can cut it off clean and just glue it on the new one.\015\012\015\012The connectors are just brass blade connectors which you should be able to get at a Ho ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

I have a 6 gallon shop wet or dry vac. The dust and dirt comes out around the base of the motor fin, not around the tank top. Now what? Oh I lost the filter around the drum that holds the ball, so I wrapped a rag around it and made it secure. Respectively: TOM

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=765231\015\012Generic problem for all Vacuums\015\012I have a 6 gallon\015\012Posted by tsfroggy on Jul ... Vacuums

My Nilfisk GWD 300s had been working fine, however today i could smell something like burning smoke from the motor, when i opened up the motor i could see a carbon metal rod touching the motor shaft a

... Nilfisk Vacuums

I was vacuuming the vent in the bottom of the fridge. I must have picked something because the motor got wildly noisey. I cleaned out hoses, etc. There is no suction. I can see the blades of the motor and they are not turning around. Model U4269-930 Series B.72. Can I get at the motor to see if something is keeping the blades from turning? What would be your suggestion. Many thanks. Pat Sauerman

Hi Pat, my name is John I will do my best to assist you.\015\012\015\012You certainly can get at the motor, with simple hand tools. \015\012\015\012Referring to this ... Hoover Vacuums

My Sharp EC-l2TWT4 throws belts and I noticed the motor shaft was not running straight. My wife took it to my local dealer in Brainerd,Mn and they said it was fine.So I took it apart and found the plastic motor housing had melted at some point letting the motor twist out of alignment. Other than this, everything works great.Can I order this plastic housing piece somewhere?

I checked the schematics for that model and the motor housing for that model is no longer available. Your best bet is to either attempt to find a used part or trade it in and get a new unit. Sharp no longer makes any vacuums or parts which makes thes ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Putting the belt over the motor shaft

The belt may be overloaded because something it is driving is jammed or partially siezed . It could be a bad bearing or string wrapped around the beater brush etc. Check that everything moves really freely before going through this again. Take it all ... Hoover Elite U5061-900 Bagged Upright Vacuum

Hi, I have Fisher & Paykel dishwasher # DD603-BK-USA. When it start to work, it becomes too noisy with a sound HUMMMMMM... I found water desn't spray from the blade. I am possitive that it could have some rust around there. I tried to reach the motor, and I cannot. May you help me how to reach the motor so I can check it.?

There is an access panel by the floor,some are just clipped on,some are fastened with screws,the motor is inside this lower area,but is is quite cramped for working space so you may need to remove the motor from the unit for testing ... Vacuums

Kirby Heritage II 2HD Vaccum Cleaner. I have removed the housing and reached the motor shaft for the vacuum fan. How do you remove the fan from the shaft.

Hi, you can visit this site to view how to remove the fan from the shaft...http://www.diyonline.com/servlet/GIB_BaseT/diylib_article.html?session.docid=1678Take care ... Vacuums

The powerhead will turn until you touch it down on the carpet then the belt just spins (burning rubber smell). Is there supposed to be a fitting around the metal shaft opposite the powerhead or does the belt ride on the metal shaft?

That means that the belt is stretched and worn and needs to be replaced. Here is the belt you need and the manual which has instructions: ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0329 seconds