Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

Handle will not release on my dyson animal

\015 You pull the wand up and it will not release from the vacuum\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Handle will not release on my dyson animal


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)


Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My dyson dc17 vacuum handle won't recline. - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


The under carriage is misaligned itself or has broken. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dyson animal's clear bin latch is stuck and won't release. I can't take off the bin via the outer shroud release either.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Cant lower handle on my dyson dc07 - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Cannot put handle on dyson - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi,Did you receive the handle with the wand already attached? It should be. Then, to get it into the hose pres the wand release button on the end of the hose and slide the wand into the hose. The wand should then be pushed into the slot o ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson spring release came apart - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Thishappened to me too. I had to order a spring kit. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc17 hose will not come out/ handle wont release from machine. i've pulled the metal rod up all the way and the handle still won't come away from the machine so i can't use the hose and attachments. anyone know what the problem might be?


Hi there, it is possible that you have a blockage in the wand/hose assembly which is making this difficult to remove. If you are able to remove it to check for this, please contact our Helpline on 1866MYDYSON so that one of our advisors c ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The release will not work on my dyson dc07 - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC17 Animal does not have enough suction from the wand handle to power the mini turbine head. The wand handle has very little suction.


My dyson doesn't have suction either and nothing is blocked. In fact is was working great the vac that is, but when I used the wand for the first time to get the corners the vac shut off, I checked the hoses, filters and all nothing is blocked. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson hose on handle clogged - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Take hose off and push broom handle through to clear the blockage this link will show you how to take hose offhttp://www.youtube.com/watch?v=6W0W4Rj3dkM ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC25 Animal vacuum head is not staying flat after pushing Red Release Bar.


... Vacuums

Beater bar stays engaged when handle of dyson animal 17 is in the up position


Hi Richard,I'm sorry to hear you're having difficulty with your DC17. The issue you've reported sounds very unusual, and we'd appreciate the opportunity to provide further assistance. Please give our customer Helpline a call on 1-866-693-9766 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson DC28 Animal. It worked fine until


Lube the little clip that holds the handle upright (get down at the floorlevel and kinda look for whaer it migh be,, i used just a lilsilicine lube and mine is fine now,,was a hard to unlock handle prior to this,, all is good now.\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I just received an older model Dyson DCo7 animal vacuum. When it is turned on and you are vacuuming, should there be suction at the top of the handle while vacuuming the floor?


No it should not ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How do I change the handle on a Dyson DC08 animal


... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My dyson dc animal's brush is not spinning. The machine smells like burning rubber. I believe the clutch has gone out but the machine also only sucks from the top of the hose in the handle. I am wondering if the machine is not locking properly which is causing the brush to not need to spin. If this is the problem how do i fix this problem.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a dyson dc17 animal. When you put the handle down, it is very loud


Hi there,When you lower your DC17's handle into the vacuuming position, a second motor which powers the brushbar will switch on, which will make the machine sound a little louder than when it's standing upright.However, if you're conc ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Electrical short in handle - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


When you say there's a short in the handle, this can really be one of two things. It can either be the switch, or the cord. Here's a link to repair that I did on how to replace the switch on your Dyson DC07: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Power shuts off on my dyson dc17 animal


I had the same issue. Got on the phone with Dyson. THe vacuum has a safety feature where if the motor gets too hot it cuts off. You have to leave it for 45 minutes or so and then it will work again. There is an underlying issue though. My proble ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I've used my brand new Dyson DC28 once and now the handle will not release from the upright position. What can I do?


Sorry to be blunt... SEND it back. It is rated poorly, -Consumer Reports - is expensive to repair and is not worth HALF the price.... REALLY - you have a valid excuse, send it back and get a Consumer Reports and check out the ratings....\015 ... Vacuums

The handle to a canvas bag got stuck in my DC 17 animal Dyson and now the brush won't turn.


The belt will stop itself from spinning if you accidentally picked up a shoestring or vacuumed the edged of a carpet and the carpet \015\012got caught. To have the brush spinning again, simply step on the front of the machine, pull back the han ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson Animal DC 28. It vacuums fine on floor mode, but, when locked in the upright position it releases pressure though the little valve behind filter a. I have only had it for 2 weeks so I'm hoping the filters don't need to be cleaned this often! I would like to finish vacuuming without waiting 24hrs for the filters to dry.


Unfortunately with any bagless vacuum the filters do need to be cleaned or replaced very frequently for the vacuum to perform. But the good news is it sounds like you have a clog in the hose. remove the attachment hose as you would be using it and un ... Vacuums

Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri


Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0360 seconds