Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?

Getting hair out of gears

\015 How do i get to the belt gears?\015

Answers :

Best way is with a screw driver and needle nose pliers. remove belt and brush first.
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Getting hair out of gears


Best way is with a screw driver and needle nose pliers. remove belt and brush first. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dc17 -too much pet hair around the belt gears


I was having the same trouble and it was driving me nuts.  I tried cleaning and it did not work.  Then I tore the brush assembly off and looked up into where the little tooth gear is.  I saw something that did not look right.  The ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!


... Roomba Robotic Floor Bagless Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dc17 -too much pet hair around the belt gears


Go to a DC14 there is a reason why Dyson calls it the Animal. It's ment for all the pet hair and things like that, listen to what Dyson recommends you, they know their products well. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Saeco Odea Giro pumps the water but the internal spline or gear is not turning moving the ground coffee grinds to the point where the water can pump to the front exit lines so the water is pumped into the over flow resevoir. How do I replace the gear or check to make sure this is the problem. I want to replace this myself.. Also how do I get the unit apart it seems to be bullet proof. Is this a common problem.


It is a common problem if it is what I think it is. However your description is a little confusing. So the coffee does get ground up, but then has a hard time getting to the next stage of the process? Please clarify... And no water gets pumped th ... Vacuums

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.


Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.


Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f


I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums

When I vacuum it leaves behind large clumps/rows of pet hair as if it was raked into a pile. I have to keep going over it to get all of the hair. I have cleaned out the vacuum and filters to help, but it does nothing to affect the perfomance of the machine. Why is it doing this?


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.


Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

There's a strip of pet hair that doesn't get picked up only on the left side of the roller, like it's rolling all of it up and kicking it out that side. I have to work from right to left to get it all up. is this a suction problem?


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Dog hair gets caught all the time in the belt drive spool, is there a fix for this other than having to pull it out all the time by hand? I have replaced the belt and the brush but this hasnt solved the problem and the belt moves so slowly and I get the loud whining/grinding noise too.


It could be either the clutch, the beater bar or the brush housing. I have included links to each parthttp://platinumvacuum.com/dyson-dc07-dc14-clutch-assembly-900252-04.htmlhttp://platinumvacuum.com/dyson-dc07-dc14-brushbar-assembly-9041 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss


Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil


Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

I am getting a lot of dog hair on the filter after cleaning one room, this is something new. I cleaned as many parts as I can. It seems like the dog hair is moving from the clear canester onto the top of the filter, any thoughts??


The cone in the tank has a black gasket make sure it hasn't slid to far up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!


First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Manual issues Have reciently purchased a kirby from ebay (gotta love ebay) but has no manual. I believe the model is a heritage (cant see a II though) Do they all have roughly the same manuals??? I have all the attactments - spray painter, hair trimmer, turbo brush etc but really want to get the most from the machine. Where do I get manuals for machines that are 20yo???!!!


Many years ago I was a service engineer for these machines in England they were actually made by a company called Scott &Fetzer in the USA and Branded KIRBY or CIMEX.\015\012\015\012See if Scott &Fetzer are still around and ask th ... Kirby Heritage II Vacuum

Hello, I have a wonderful Dirt Devil vac for my carpets, model 140000, love how it works to get doggy hair off my carpet! But, I have a cute cannister model for my laminate floors and it uses the Q bags, but they are no where insight to get or order. Can you help me with this dilema?? Anna


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=821035\015\012Generic problem for all Vacuums\015\012Hello, I have a wonderful\015\012Posted by dutchtr ... Vacuums

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

I have two dogs and while vacuuming on the back stroke I get a black line of dog hair. I have to keep running back over the same spot to finally get it up. It doesn't do it on the forward motion, .


That's natural.. vacuums pick up the dirt on the back motion (going against the grain) ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My swivel sweeper 2 caught a carpet string and stripped the small plastic gear on the motor. How can I get another gear so I can repair my sweeper? Thanks, Ivol Caudill 419-243-3916 [email protected]


We were able to find every part ofr the swival sweeper exact for the gears you are looking for.\015\012You can get a new complete sweeper head for 19.99 at:\015\012 ... As Seen On TV Swivel Sweeper Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0373 seconds