Having problems with your Dyson DC17 Animal Bagless Upright Cyclonic Vacuum ?
DC-17 - Reattaching the U-Bend piece in the back of the machine
\015 After taking the U-bend piece off of my DC-17 to clean the machine, I cannot reattach the piece. Specifically, the piece will not re-latch. Can someone explain this process to me so that I can reattach the piece?\015\012Thanks!\015
On the back of the machine you will see 2 guides where the peice should just slide easily check for dust
Repair Help & Product Troubleshooting for Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
DC-17 - Reattaching the U-Bend piece in the back of the machine
On the back of the machine you will see 2 guides where the peice should just slide easily check for dust ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Vapor Clean TR 5 Under "maintenance" they told me to unscrew to empty refill tank. After doing that, no water came out and the piece that the scew went into is now in the tank. It is too large to get out and even if you put the screw back inti that piece ir still goes into the machine. Can I still use the machine? brand new only uded it once
I is really needed to check this with the manufacturer! See contact details below: ... Vacuums
Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems
Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums
The instructions, maintenance, said to unscrew the bottom to empty refill tank. I cannot screw it back because the piece it screwed into can not come out. It is inside the machine. Will this hurt the machine if I use it?
No you can use it like that, it will be fine. ... Vacuums
Vacuum leaking? on the lower left of the back of the machine, there is a molded round piece about the size of a half-dollar. when I tirn the machine on and cover this round extrusion, vacuum power increases. what is it?
I don't know your particular model but it sounds like this is either where the hose attaches or a spot to help clean out anthing that might get stuck in the hose while vacuuming. Hope this helps! ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
The needle is to the left and back of center, frequently hitting the plate and breaking. The hoop came unsnapped while embroidering, and caused needle to bend, stopping the machine. That was no doubt when the shaft that holds the needle became askew. How do I reposition it? I don't see an appropriate category listed below. Small appliances is as close as it gets, which does not give me a high level of confidence of having an expert for my Babylock Espree EM2 embroidery machine on your staff
I work on my wife's sewing machine all the time and saw your post when I was about to leave but I have a couple of appointments to go to.Although you say yours is for embroidering,it should not matter.When I get back I will take a look around and see ... Vacuums
I own a singer sewing machine model 4562 and tension assembly came unscrewed and now I don't remember how to put the pieces back together. Do yo have a diagram that can be emailed to me so I can put it back together? Thanks
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????
Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have the Sharper Image EV-HD15 Cool Mist Humidier Ultrasonic 1.6 gal humidifier. I purchased it last year. Yesterday I took it apart to clean as per instructions. I feel that I may not have place the round housing (which is secured with 4 screws) back correctly. When I turned the machine on it made a whirring sound. I took the unit apart again and rotated that round piece moving the opening away from the opening on the tower. The whirring sound was reduced but there was still a sou
... Sharper Image Vacuums
My Dyson DC14 Animal doesn't have the suction it used to. The piece in the back on the bottom - a flap it appears - stays open now, causing the machine to make a louder noise than usual. At first, if I put my hand on the flap opening it would close, allowing for normal suction. Now, it stays "open" permanently", causing the loss of suction.
Hi its Darran at Dyson.Having had a look at a DC14 here, I am unsure as to the part you are referring to. So that we can help you further, please contact our Helpline free on 0800 298 0298, between the hours of 7am - 10pm, 7 days a week. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Took apart my cleaning brushes and all on my bissell spotbot i need diagram of how to fit the head part back to the machine. I had a problem with the auto not working i have fixed that problem just need to see so that i can get it back togoether. I assembled the whole wheel back but cannot caonnect it to the machine LOL
... Bissell 1200A SpotBot Pet Robotic Vacuum
Kenmore PowerMate cannister: Reattach cannister floor piece.
You need to open the head by gently squeezing the light cover housing and lifting it off. There will be two screws underneath and once removed the lid will lift off and reveal the area where the pedal installs. ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work
It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m
... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.
I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity
I can't get the vacuum to **** and can't get to the point of the clog. The pieces don't come off. Also need to know how to get the filter piece off the machine.
This link is for the manualhttp://www.dysonmedic.com/PDF%20docs/dyson_dc18_owners_manual.pdf ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
The tension knob came off of the front of my sewing machine while I was sewing. I cannot figure out how to put it back on. I have the metal rod that fits into the back of the tension knob, but cannot figure out how to put it back into place. Keeps falling off
It sounds like your machine is the kind that has a knob with a 'set screw', a teeny tiny screw that tightens and holds the thing in place on the rod. Look for a small hole, probably on the bottom and look for a very small screw near the machine. ... Vacuums
I carried my machine in for repairs, when picking it up, I can almost promise that I received a different machine back. The serial number is N925608167. Is there a way that u can look it up and let me know what year this is. The machine that I carried in had a built-in cutter, this one does not. I purchased in 1998 and it was practically new hardly used, but this one looks old.
If you still have the manual or receipt for your machine, it may have the serial number on it.\015\012When they accepted the machine, they should have given you a pick up slip that included your personal information AND the information of your ... Vacuums
I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t
... Dyson DC25 Vacuum
I shipped my brother PE 770 embroidery machine purchased sept of 2010, to a lady who perchased it on ebay. Had used only once. Everything worked fine.I shipped in the original formed styrofoam box. I removed the embroidery arm, releasing the locking plastic hook holdind the machine and the arm together. When to lady removed the machine first in the original plastic shipping bag, two parts fell out. Her photo she emailed showed a black plastic piece with two holes or pivot points.also a silver me
This is a link to the manual for this machine. Do you see a picture in the manual of the parts you are describing? Reply with a part number and I will do my best to help. ... Vacuums
Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance
Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum
LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.
Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
I have a Yamata GK367B refurbished machine, an older model and the manul is mostly in Chinese and very bad pictures. I need better information about how to thread my machine and to set the tension correctly. I am a professional and need this machine. But it has never worked correctly since I bought it and the company will not take it back. So please help me. Jill G. Arellano
We have no material at all for this brand, sorry. ... Vacuums