Having problems with your Dyson DC18 all floors Bagless Upright Cyclonic Vacuum ?

Brushes won't turn remain motionless as if cleaning hard floors even though button depressed could it be a problem with the brushes or button still under guarantee

Answers :

There is a re-set button located on the brush head on the left side as viewed if you are standing directly behind the vacuum cleaner. It is black in color and is recessed slightly into the cover of the brush cover. It is round and about the size of the head of a country match and sticks up about 1/2 inch. Just press it to reset. Also, don't forget to press the grey on-off brush switch located beside the red on-off which is located near the top of the handle. Hope this information solves your problem. [email protected]
Repair Help & Product Troubleshooting for Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes won't turn remain motionless as if cleaning hard floors even though button depressed could it be a problem with the brushes or button still under guarantee

There is a re-set button located on the brush head on the left side as viewed if you are standing directly behind the vacuum cleaner. It is black in color and is recessed slightly into the cover of the brush cover. It is round and about the size of t ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?

Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

I have a Electrolux Epic 6500 SR canister vacum cleaner. It is nine years old and for the past few weeks it has started shutting off for no apparent reason.The symbol for bag change lights up and it cuts off, but even after I have put a new bag in, it still does the same thing. Do you have any suggestions? There is a little button or switch that the top of the bag fits on. Do you think it could be the problem?

Your machine is probably clogged, look through the wands, look in the bottom attachment, to see if there is anything stuck there. You can also drop a marble through the hose itself to see if anything is stuck there as well. To unclog the hose try hol ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

I have the LG Kompressor Luv3008. It recently started but refuses to **** up the dirt despite the noise and motion of the brushes. I noticed that the filter near the head is also very warm. Even though I cleaned out the bag what could be the problem? How do I fix this?

... LG Vacuums

Electrolux vacuum brush not turning problem: was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won't even switch on. Hope you can help

Under the vacuum, there is a guard.\012remove the guard , either by 2 screws or by 2 clips.\012there is a belt under the guard.\012that is connected to the brush.\012the belt need to be replaced. ... Vacuums

I have a similar problem as many do with this model, "clean Roomba's brushes".. We took it apart last night, cleaned out all of the dust we saw. we removed the cover, the housing for the brushes and everything else we could. Still has the same problem. What now?

Mine did the same thing and no mater how much I cleaned the brush or pulled fibers of the ends it did not stop until I:Removed the little yellow tabs on the ends of both brushes and used a tooth pic to remove the built up inside the bearing ass ... iRobot Roomba 530 Robotic Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to

... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson dc24 brushes do not work even when i depress the silver button

Hi there Alison, it's Jack at Dyson.DC24 is equipped with a safety device which shuts off the brush bar if something jams it - for example, a shoelace or a rug fringe. From what you've described, it sounds like your machine may just need rese ... Dyson Ball DC24 Bagless Upright Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

H300 brushes won't stop spinning even though I switch it from "wet scrub" to "wet/dry pickup" and is leaving streaks on the floor. I have already ordered a new squeege, but that won't take care of the non-stop brush problem. Any suggestions?

I have found that the plastic piece on mine is wore out and slips when the trigger is pulled back. If you look underneath the dirty tank, you will see the black plastic pieces that over lap. I took a wiretie/zip strip and placed it around the spot ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.

... Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

Vacuum motor overheating. Never happened before till last nite and today. It seems to be getting hot and tripping an overload switch or something like that. Starts back up after a long cooldown. Roller brush will still come on, even though the vacuum motor will not. Any idea what may be causing that?

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a 4 showing on the screen of model 48465C, cannot remove it is not for the number of hours to brew, however only brews 4 cups of coffee, even though I have push the button to remove is still there.

Well... to start.... you are on the vacuum area.... can not help here!!!! ... Vacuums

My electric toothbrush doesnt work any more even though I have only used it a dozen times. I have obviously tried to charge it, but with no result.I disposed of all the packaging when I started using it so I dont have the guarantee. I bought it from Tesco in Roundhay Rd., Leeds 8. roun about Christmas time. I would be grateful if you could help me with this matter. Yours sincerely, Mrs. L.E.Glenn

My Dear Chap. It is highly unlikely that you can exercise any type of warrenty for the toothbrush without the documentation. That is, a reciept at the least. Packaging would have helped, but the receipt is the key.\012What you can do is try to ... Vacuums

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?

I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

My central vaccum cleaner has no suction at all outlets even at the canister. The motor is still working and blowing air out the air release tube. What could be the problem

Check the filter in the tank. If this is dirty, the motor will still run, but there will be little to no suction. Rinse thoroughly under warm water, then allow to thoroughly air dry before replacing into vacuum. \015\012I recommend having tw ... Electrolux Central Vacuum

The spin brush in the head is not working. I have tried the button which supposedly activates it, but it is still not working. How can I fix this problem?

You will need to replace the yoder loop with in the head. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.

Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

I have hoover mdl U6459-900 and the brush will not rotate even though the main pulley belt is rotating. i have changed booh belts and this did not solve the problem. the suction on the unit seems ok. thanks??

Sound like you need tear down and find whats jamed in it to stop it from turning like string ore hair ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My hoover steam vac is leaking. the water seems to come out where it should by the brushes but it all leaks out even when not depressing the button. seems to be suctioning fine.

The problem you describe is a bad resevoir. I have replaced a few in this model series. Take it to an authorized dealer for repair. ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Vacuum either stops for no reason and can't be restarted without unplugging and waiting 1/2 hour to restart, or it simply will not turn on at all. The red light comes on when the "On" button is pressed. I took it back today for the 4th time in a month to where it was purchased. They called later and said it was running fine and they could not detect a problem. The last three times they have (1) replaced the roller brush, (2) "unclogged" the vacuum, and (3) "adjusted" the belt.

This sounds like it might be an overheating problem. \015\012\015\012Some vacuum motors are fitted with thermal cut out fuses or thermistors which cut off the flow of electricity to the motor when the temperature gets to high. It is possi ... Lindhaus Activa 30-38 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0815 seconds