Having problems with your Dyson DC25 All Floors Bagless Upright Vacuum ?

My brusg stopped turning after sucking up a shoe

\015 My brush stopped turning after sucking up a shoe string. I have removed it and anything else that may be stopping it from turning but it still don"t work. What do I need to do?\015

Answers :

Hi There is a reset switch on your Dyson that needs to be pressed when something gets stuck in the brushes. The reset switch helps protect the motor that spins the brush from damaging if something gets stuck inside the brushes. There is a little red pole that sits up behind the brushes on the vacuum head, I believe it's on the left side of the floor head as if you were behind the machine vacuuming. Try pushing this reset switch first. Did this fix your problem? If no, please let me know and I'll be more then happy to do some more advanced diagnosing with you.
Repair Help & Product Troubleshooting for Dyson DC25 All Floors Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My brusg stopped turning after sucking up a shoe


Hi There is a reset switch on your Dyson that needs to be pressed when something gets stuck in the brushes. The reset switch helps protect the motor that spins the brush from damaging if something gets stuck inside the brushes. There is a little ... Dyson DC25 All Floors Bagless Upright Vacuum

I ran over a shoe string. Turned the vacuum off and pulled it out. Now the wheel wont turn and it isnt sucking up the dirt.


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

It stopped sucking @ brush stopped turning - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Usually on this vacuum those two problems are not related, but if you got a lot of stuff stuck in the brushroll and in the suction tube at the same time it could happen. Check the belt to make sure it's not broken. If the vacuum is over a year old th ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I sucked up a shoe string. It pulled out easy, but now the brush wheel won't turn or suction.


Take the brush roll sole plate off and make the brush roll is properly sat in its housing, also the belt isnt broken ... Dyson Vacuums

Beater bar stopped after sucking up shoe lace


Hi choward40,Yah, vacuums don't particularly care for shoelaces! :>) Did you get the shoelace taken out of the beater brush?Did the shoelace go all the way into the machine?Please reply back. Thanks, ... Dyson Vacuums

Using a Hoover Steamvac to clean my carpets. It works fine in some areas, but others it makes a clicking noise and stops sucking water. Once I turn the vacuum off and wait a few seconds, it clicks once more and is okay to use again. Certain parts of my carpet this happens so frequently I can't vacuum.


1)clog in the hose or air/tank full you must , need replace or emptied,test the belt for broken or worn.2) noises can be area motor , test for fan blade defective or broken3) You must go http://hoover.com/support/video-instruction-guides/ for ... Vacuums

My Eureka Endeavor NLS is about a year old and stopped working. It just blows dirt everywhere when turned on. There is some suction to the hose part but only when it is flush against your hand or floor.Other than that, it will not suck anything up.


... Vacuums

Wife sucked up a nickel cleaning daughters car. Vacuum stopped, smoked before she could turn it off. New motor? Is it worth it? How much is a new motor? Thanks in advance. Jim Troup [email protected]


You can buy a new motor HERE and we will install it with no additio ... Kirby G4 Bagged Upright Vacuum

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?


If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson just stopped sucking up dirt. I have checked all the obvious things like clogs and filters. I noticed when I turn it on, there is a valve on the top of the cannister that opens and you can feel suction from the vent hole. Is this valve malfunctioning, or is it working correctly because something else is malfunctioning?


Your cyclones could be clogged. You can clean them yourself pretty easily. See this video. http://www.youtube.com/watch?v=2OO3ugkyzxk ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I accidentally sucked up a thin belt that wrapped around the bristles and stopped the bristles and now the bristles wont turn


You need to remove the thin belt from the roller if you haven't already. Check the ends of the roller to make sure there is nothing there stopping the roller from turning. You can try turning the roller with your hand using minimal force. \0 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Light burned out and at same time sucking motor stopped working. Brushs still turns. is there as fuse I can change out or is the motor toast ? this unit is less then a year old


Contact your local warranty center they have had problems with that model ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes


Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The rotatory brush stopped turning after sucking rug fringe onto it. The belt looks fine. The suction is fine.


Found on website "dysoninfo.com"A problem I have run into a couple of times at home, generally when I am cleaning the bathroom, is that my Dyson brush won't turn. First off I would say be sure to check that you haven't press ... Dyson Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

My Dyson turns on and is not sucking. It makes a


I have the dyson dc 27. On the bottom left back side of mine there is a circle, and ball inside of it. I turned it on and pushed the ball and it started working again. Sometimes it doesn't cover the whole and stops sucking air through it. ... Dyson DC07i Bagless Upright Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Restrictive valve moments after starting the vac the red ball rises to the top and the machine quits sucking. I turn the machine off, the ball drops, I turn the machine on, the ball rises the machine quits sucking, I turn the machine off the ball falls, I turn the machine on........etc. What am I doing wrong? It works fine and then all of the sudden it starts the same stuff again. I thought it was because the retrieving container was getting too full or the cleaning soln container was not full e


The foam filter on the bottom of the tank lid is too far up. Pull it down so you have at least a 1/4 inch gap from the top. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The Kenmore grab n go was sucking fine and then stopped sucking.


Did you check to see if it is clogged? ... Kenmore 34723 Grab-N-Go Upright Vacuum

Machine turns on, has little suction, then stops working.


It would be helpful to know what model of vacuum cleaner you're talking about. Basically though, your machine has a blockage somewhere (hence very low suction), and is cutting out after just a few minutes because of overheating.  You need to exp ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.


The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!


Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue

Motor bogged down, smelled rubber, brushes stopped turning


This repair would require motor replacement, based upon your explanation. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My oreck vacuum has stopped sucking up things.


It won't turn the brush because the belt is stretched or broke from the heat of sucking something too big up. If you have your service manual it should show you the location of the belt covers to replace it. ... Montgomery Ward Oreck XL Celoc Hypo-Allergenic Vacuum Vacuum

When the power head is turned on it goes from green light to red light and stops. The belt is fine and there is no obstructions in the brush to stop it from turning.


This will happen only when the brush or motor does not turn the right speed \015\012make sure to pull the end caps off the brush and clean any hairs or fibers from it\015\012the motor you can try and turn it by hand with out the belt on a ... Fantom Vacums Lighting Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0489 seconds