Having problems with your Dyson DC25 All Floors Bagless Upright Vacuum ?

Motor not running but brushes rotate, makes weird sound

\015 We do have a lot of dog hair around here, tried to clean out the parts that were clogged up, but motor just makes a sounds like it's stuck.\015

Answers :

Thats decouse it is,,,it could well have burnt out if it got "cooked" becouse it was blocked up with dogy hair they get very hot and just melt?
Repair Help & Product Troubleshooting for Dyson DC25 All Floors Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Motor not running but brushes rotate, makes weird sound

Thats decouse it is,,,it could well have burnt out if it got "cooked" becouse it was blocked up with dogy hair they get very hot and just melt? ... Dyson DC25 All Floors Bagless Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Dyson dc25 all floors is making a weird screeching sound and it smells like the motor is overheating within the first 15 seconds that i have iti running. any ideas?

Could be the clutch that's causing the problem. I suggest taking it to a local vacuum shop or calling Dyson and explaining to them whats happening. ... Dyson DC25 All Floors Bagless Upright Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.

Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

My Dyson CDC14 Animal just started making a wierd sound coming from the rotating brush area. I already cleaned around the brush, sounds like a fast rattling sound.

Hello,Something could be jammed, or not rotating freely, maybe an improper alignment with the brushes, or a blocakage within them. Try to re adjust the brushes :) ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums

DYSON DC14 While vacuuming the living room, the rotating brush started making an awful loud grinding sound. We opened the intake port, cleaned the brush but to no avail sound still persists once you lower the vacuum handle in an attempt to clean. Was wondering if there was anything that can be done?

Take the bottom plate off and check the belt. Also, rotate the brush by hand - it should turn with only a moderate resistance from the belt, or very little if you take the belt off. If it is hard to turn, or if the belt is stripped-out right where it ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!

Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.

... Vacuums

My Dyson DC 15 makes a horrible noise when switched to do carpets - sounds like gravel in the motor - and then comes the burning smell. Nothing keeping the brushes from moving, and I think they are. I am concerned that it is a belt or the motor. How do I know?

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you

Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?

Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

7600 model - motor runs and good suction present Does not self propel and brush does not rotate although I can turn it easily

Your brush drive belt has broken. Generally you need to remove the bottom of the machine in order to get to it. On the belt you should see numbers even if you don't, just look on the bag that the new one comes in for the brand and model you have. Bel ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hi, I have a 560 series. It has worked great but now the brushes won't turn while on the floor (I can turned them by hand)and it makes a clicking sound. The drived motor seems good. Nita

... Roomba Pro Elite Bagless Robotic Vacuum

The brush won't rotate & makes an awful sound. I have cleaned it, so there are no obstructions...how can i fix this?

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Has a Bissell, Pro Heat 2X rug shampooer. It powers up & and the motor runs but the brushes are not rotating and water is not being dispensed.

Brush roller not working and water not dispensing was mostly caused by a brush belt being broken or is out of place.Turn the machine off and unplug it if the Brush roller do \015\012not turn. Remove any objects caught in the brush roll. A ... Vacuums

Sebo X4 is squealing when pulled back. Takes a while after it's been running for this to happen. We changed the roller brush (needed it anyway) but didn't take care of the noise. Could the wheels be making this sound? At least that's what my staff thinks is going on... I own a commercial cleaning company and all we use are sebos... they're an amazing machine!

Yep - we think Sebos are pretty good too. I work at a Sebo sales and repair dealership! The wheels are a good bet - I can't think of anything else that might cause the noise. If in doubt, I suppose you could simply wheel one around for a while when s ... Sebo X4 Bagged Upright Vacuum

The motor makes a weird sound and starts to heat and smell like something is burning

If the motor sounds scratchy and is making a burning smell, or sparking you will need to replace the motor or the entire vac. Carbon brushes will rarely fix this as it is a high RPM motor ... Kenmore 25512/ 25513 Progressive Canister Vacuum

The head on my canister vac vibrates, smells and makes a bad sound. When I took it apart the inside of the "end brush tufted" piece had bits of the plastic broken off. Should I replace the Agitator Unit Assy or could this be the motor?

If you are talking about the end cap is broken off the agitator, I would replace the agitator. you can check the motor by turning on the vac without the roller installed. ... Vacuums

Motor runs vacuum has suction on attachment but brushes won't Rotate

This problem is most often caused by a broken brush roller belt. Sometimes, although very rarely, there is a separate motor which turns the brush, or there may be something that is causing brush roller to bind so that a belt does not last long. I do ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

When I turn on the rotating brush the vacuum makes a horrible sound. How do i fix it?

Ok, after long call with thech support I found it is bad bearings in the roller brush. So that needs replaced. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Doesn't suck I have a Hoover Empower. The motor runs, but it is not sucking anything up and the brushes aren't rotating.

Every vacuum needs to be occasionly taken apart and throughly cleaned. Usually when the brushes don't rotae it's a belt. But sometimes it's because junk gets wrapped around the roller. Things like string or thread or fiber that wounds around the r ... Kenmore 35912 / 35913 Progressive Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0897 seconds