Having problems with your Dyson DC25 All Floors Bagless Upright Vacuum ?

My Dyson DC25 keeps blowing off the filter within the ball. It then stops the ball from rotating freely. Will a replacement filter solve the problem? Sear has no clue they "THINK" it's the filter


Answers :

Ive just been onto Dyson and they have sent me a new filter . i mentioned 2 other parts that were broken and they're sending those too . All free of charge , RESULT !!!
I would try the filter first. The filter on your unit should be replaced at least once a year, more often if it gets used a lot or in a very dusty or dirty environment. If the filter is clogged air cannot pass through it just as if you laid a piece of plastic over it which can cause it to blow off.
Repair Help & Product Troubleshooting for Dyson DC25 All Floors Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Dyson DC25 keeps blowing off the filter within the ball. It then stops the ball from rotating freely. Will a replacement filter solve the problem? Sear has no clue they "THINK" it's the filter


Ive just been onto Dyson and they have sent me a new filter . i mentioned 2 other parts that were broken and they're sending those too . All free of charge , RESULT !!! ... Dyson DC25 All Floors Bagless Upright Vacuum

My Dyson DC25 keeps blowing off the filter within the ball. It then stops the ball from rotating freely. Will a replacement filter solve the problem?


I just started having the same problem. Did you figure out yet? ... Dyson DC25 All Floors Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?


Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums

Our problem with our Rainbow E Series is that it has sucked water up and blown it out through the lower part of the hepa filter, making the filter wet and dirty. This had happened before and the repair shop did not see any problems with the machine, so we replaced the filter and were very carful not to overfill the tank and to change the water often. Now it has happened again and ruined another filter. Do you know what could be causing this issue? Can the filter be cleaned or will a new one be


Thank you for allowing\012us to help, please respond with further questions and concerns\012\012Spanish speaking\012available for all problems\012\012 ... Rainbow E series Canister Wet/Dry Vacuum

Does the hoover runabout u427-930 have a filter? I replaced the belt and next to the light bulb was a square gray mat that looked like a filter covering a screen full of holes that looked like the motor was behind. I think it was a mat of cat hair so I took it off and threw it away; I just want to make sure that it wasn't a filter that I need to replace.


From doing a search on the internet and hoovers website it looks as if this unit does not have a filter. Such as a hepa that needs to be replaced or that is washable. So i think you are safe and dont need to worry about it. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Clutch replacement I have a dyson DC7 animal that is having a clutch problem, I have the repair manual on how to do it, my question is what other things should be replaced while I have it all apart. ( ie belts, filters, etc? ) The unit is about 2-3 years old and this is the frst problem we have had with it


Go to http://www.youtube.com/watch?v=7_CtaFcc5HU to see how to remove clutch. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I replace the hemp filter? Is there more than one? of course I've misplaced owners manuel, I've had it since July 2010, live where there are 3 indoor cats, I'm allergic to cat dander, for the first few months no problems with vacuum stirring up dander, however now, when vacuuming, my lungs start to close up. Definitely problem with the filtering system. Help! Today is 3.22.11, it's 11:24 am. Thank you.


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Low suction Replacing filters....need help replacing the belt - anyone know how? But before doing these things, have had a problem with suction....I'll let you know if the problem clears up.


Hi, You can take care of both things at once. Here's how:\015\012Unplug and flip your vacuum over, beater bar side up. Remove the cover base plate that surrounds your beater bar. It's held on with either clips or screws, and usually "hinges ... Eureka 2961AVZ Bagless Upright Vacuum

Dyson DC25 filter within ball keeps dislodging


... Dyson DC25 All Floors Bagless Upright Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover Windtunnel T-Series UH20700 9 mos old. Keeps clogging in hose just above the beater brush assembly. I think it clogs because the suction is too weak to pull much through. Primary filter is clean and HEPA filter is replaced. Even when everything is unclogged, suction is weak compared to another unit (same model) that a friend has. Any ideas?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

I was trying to repair my wife's kitchenaid mixer and took part of it apart, including the back part, where the electrical connections are. The original problem was the plastic gear was damaged -- I finally had the good sense to find the solution for that problem on the internet and replaced the damaged part. But now the mixer just won't turn on. I don't think I damaged anything in the electrical section, but I suspect I either blew a fuse or somehow disconnected something.


Do you have a model number? Is the voltage getting to the motor from the switch? ... Vacuums

I have a shark transformer Vac EP602RF. I want to know how much the filters cost. My daughter threw the non-woen pre-filter away thinking I had replacement ones.


... Vacuums

Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?


Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a qsp shop vac 10 gallon upright need elastic and filter sears is where i purchased it but can't find the replacement filters


Try e bay. ... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Noisy vacuum I have a eureka capture that I bought in april it's making a horrible high pitched squeal type noise, I have made sure my roller is clean, my filters are clean, i replaced my hepa filter and there are not any blockages I don't know what else the problem might be. Could you please offer other suggestions to fix this?


... Vacuums

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.


I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.


It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

I have the same problem as steve967 The dyson dc16 is fully charged, runs well for 5-10 seconds and shuts down. I wait for a second or 2 and it runs again for 5-10 seconds. This will continue for numerous cycles, until I am finished cleaning. I have cleaned all the filters, and the power is good, The system will just not stay on. It is just over 2 years old. A friend of mine had the same problem with his Dyson DC16 after just a couple of months and has replaced his Dyson with a Black N De


Dear Michael_Stad,I am going to sound like a broken record but here is my same answer to another person with the same problem.I have I had the same problem with my Dyson DC16, where it only runs for a few\015\012seconds at a t ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

A 'burn' hole has appeared in the Microwave Outlet Cover causing arcing (or similar sparking and blue flashing!). Would replacing this cover with a new one solve the problem or does it suggest something that would quickly reoccur? Would it be an economical repair or should we ditch the machine for a replacement? Thanks in advance etc it is appreciated.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0680 seconds