Having problems with your Dyson DC25 All Floors Bagless Upright Vacuum ?

The bottom bar does not rotate. I took it out and inspected for jams, etc, and found none . it is plugged in, and will rotate by hand with some resistance.


Answers :

Hi, there is a button next to the start button, this works the brushbar. The brushbar is optional for different floor settings
Repair Help & Product Troubleshooting for Dyson DC25 All Floors Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The bottom bar does not rotate. I took it out and inspected for jams, etc, and found none . it is plugged in, and will rotate by hand with some resistance.


Hi, there is a button next to the start button, this works the brushbar. The brushbar is optional for different floor settings ... Dyson DC25 All Floors Bagless Upright Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

While vacuuming my carpet, a corner of a throw blanket was sucked into the beater bar. I turned the vacuum off and was able to pull the corner of the throw blanket out without much resistence. I plugged the vacuum in and started it and now the beater bar isn't rotating.


Try pressing the reset button on the nozzle, probably just tripped out the brushroll motor ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

My miele S277i will not start up The fuse is ok in plug etc Wire not broken anywhere When I opened it up I found that Power is getting all the way to the motor brushes in fact. Any ideas?? Regards Andy


Hi, \015\012\015\012Usually when a Miele doesn't start it's one of several things. Most commonly the cause is a faulty cord reel, however if you get power all the way to the motor brushes, it sounds as if you cord reel is ok, and that an ... Miele Vacuums

I have a bissell proheat turbo2x the brushes wont rotate checked for blockages none to be found can anyone help


The belts are probably broken, stretched or worn. I would try replacing the belts if you haven't in a while. You can get the belts you need here: ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My dyson dc18 has no suction, i havent found any plug in the tubing etc? there seems to be air blowing out around canister, is that normal? Help, any suggestions?


... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

Omc specs 1989 rinker boat 4 cylinder gm/omc i need specs for: plugs, points,idle, prop size,etc. boat had been sitting for a while, i changed oil,points,plugs, new gas,etc. i can crank it, but it's a little rough and won't idle below 2000 rpms. any advice or help would be appreciated. thanks. tommy


You will need to repost this in the correct section, this one is for vacuum cleaner repairs. ... Vacuums

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.


If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I have a dyson dc14. the brush bar will not rotate when the vacuum is running. the belt is attached and it will rotate by hand. when you switch from bare floors to carpet-the bar will not kick in and rotate.


\015\012Hi,\015\012Check that when you pull back handle to vacuum the clutch control knob which is located front lower left side of machine moves to drive position & is not stuck in off or park po ... Dyson Vacuums

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.


Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

My roomba 560 has brushes that spin one rotation then stop then you hear a click and they rotate one rotation stop over and over. I took compleatly appart cleaned, lubed, and inspected all looked good?


Here's the solution to this problem...\015\012\015\012Remove the rollers and run the Roomba and see if the problem goes away. If so, here is the solution to the problem...\015\012\015\012Each roller has a little yellow cap on ... iRobot Roomba 560 Robotic Vacuum

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron


The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live


... Vacuums

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy


Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.


I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

I have a Vacu Queen V3000 and it stopped working in the middle of a job. I verified that I have power at the outlet that it plugs into and then checked motor resistance from the plug and I got about 600 ohms. What is the problem?


EMRS, Hahah the same thing happened to mine... the lid cracked and I used PL Construction adhesive, it has held for a year, but needs constant gluing. Where can I buy a new lid relatively cheaply? Can't find one in Canada. ... Filter Queen Majestic Canister Vacuum

Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.


You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hi...my dyson cylinder vac,DC08will not start when plugged in and switched on...after working fine yesterday...have checked plug etc. Any ideas??? Thanks.


Hi its Darran at Dyson. If the machine had been left overnight and then would not switch on the next day, then this sounds as though there may be a problem with the switch or the motor. So that we can help you further, please ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I have a model 116.35922 beltless drive vacuum. The agitator brush will not turn with the vacuum running and the handle down. The brush turns by hand and the reset button has not popped. Ther is nothing wrapped around the brush, but it does feel to have some resistance when moving by hand.


Wich bags for vacuum cleaner kenmore model 116.35922 ... Kenmore Vacuums

Kenmore 39522 vacuum beater bar keeps rotating after unit is shut off. Even unplugged it to move to another room and when I plugged it back in, the bar rotated a few more times! Has a definite clicking sound when this happens. Purchased in January 2008.


The berings or something inside might be going bad. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0364 seconds