Having problems with your Dyson DC25 All Floors Bagless Upright Vacuum ?

The brush head does not lower all the way to the floor

\015 When I step on the red lever the brush head is not released completely. just happened without any notice. HELP!\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC25 All Floors Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush head does not lower all the way to the floor

... Dyson DC25 All Floors Bagless Upright Vacuum

Clarke scrubbers helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? ther

... Clarke Vacuums

Clarke Instructions helo there. on the front brush head assembly the actuator motor that lifts the brushes up and down from the floor has a sleave and a finger that turns the motors on and off. when the head is lowered it comes on and brought back up it turns them off. this assembly controls when the pads start to spin and also determins the downward pressure of the pads affecting the cutting and or cleaning pressure onto the floor. how do i adjust the height at which the motors turn on?? t

... Vacuums

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.

Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

Steam-it floor head brushes

My guess is probley used for low carpets or kinda like a dirt pusher just for a add on just for looks ... Oreck steam-it Stick Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

Shark navigator power head will not turn on unless main handle is lowered to the floor

... Dyson Vacuums

I have an eureka power plus vacuum floor cleaner and i have no way of opening the botton to the brush to change my belt for the brush since the brush will not turn.

Look for two screws at the edge of the brush housing. You may see these ones on top. They will be black and recessed ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look

... Kenmore Vacuums

Henry brushes seem to catch in the carpet when pulling-will the brushes soften and make it easier to use as it makes the head bounce of the floor a bit when pulling making it harder work to vacuum?

There is a "see-saw" type switch on top of the cleaning head (the part that you push across the floor). This raises and lowers the brushes according to the type of floor you are vacuuming. Move this switch to the other postion and you will find that ... Henry Vacuums

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.

Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Can I buy a new power head and floor brush head for the harmony....bought in 2004-05 and if so where?

Hi, EVacuumStore.com sells a good selection of parts for the EL6985. If they don't have the parts you are looking for, try ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

There is no suction from the head on the floor. The hose is sucking properly but not the floor brush. I have checked for blockages and can't find anything - any ideas?

I have exactly the same problem!\015\012i think it is something to do with the transfer hose that changes the suction from the hose to the brushes ( it is at the bottom left of the machine as you look at it from the front! ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brushes not contacting floor

It is unlikely that you have worn the brushes to the point that they no longer contact the floor properly unless you use it daily and have a very rough tile or concrete floor and even then they should outlast the machine. It is more likely ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.

The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Brush will only spin when slightly lifted off the floor. If all the way to the carpet it does not spin. Is this a belt issue?

It does sound like the belt could be stretched -- may need replacing. Would also suggest cleaning the roller axles / bearings / housing and lubricating with machine oil. WD-40 works well for cleaning same.\015\012\015\012Charlie ... Vacuums

Dc25 brush bar head won't lay flat - Dyson DC25 All Floors Bagless Upright Vacuum

... Dyson DC25 All Floors Bagless Upright Vacuum

Dirt Devil 086905 has suction through hose, but will not **** at the power floor head. Cannot find a clog, brush spins. What should I be checking?

Need to take the head apatr as if you were replacing a belt. Look for the clog... it's there ... Dirt Devil Vacuums


Can you hear the motor for the brush turning. it sounds like the belt will need to be replaced. ... Vacuums

My vacuum does not suction floor debri the canister says change bag, i changed it 2 times with recommended electrolux bags. It will suctionwith wand and brush but not with power head

\015\012The power head has a separate motor to drive powerful carpet cleaning.Check if that motor is getting blocked or if its running slow/weak.Also check from any blockage in vacuum line.\015\012Keep updated with the results.\015\012Than ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

While the windtunnel is upright the suction is awesome. When you lower it and engage the brushes is looses suction. It will not pickup anthing on the floor

Check the brushroll if it spins freely, replace the belts 38528-034 and 38528-035. and make sure the tensioner for the V belt engages when you release the handle and pull the head back ... Hoover U8361-900 WindTunnel 2 Bagless Upright Cyclonic Vacuum

I have a new Euro-Pro shark model S3101. Used it one time and while I was doing my tile floor in my kitchen I reached under a cabnet to clean and hit the floor kick kind of hard and broke the head off of the shark. I have only the T shaped end on the shark now with the cleaning head broken off and looks unrepairable. I did kind of hit the floor kick hard but the plastic broke like glass. Can I put a new head on the remaining piece or is it repairable? thanks Angie

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Pro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0820 seconds