Having problems with your Dyson DC25 All Floors Bagless Upright Vacuum ?

When putting the hose back into the dc25, it extends so far that the flap at the bottom opens causing no suction when using it uprightWhat's your problem?

Answers :

Repair Help & Product Troubleshooting for Dyson DC25 All Floors Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When putting the hose back into the dc25, it extends so far that the flap at the bottom opens causing no suction when using it uprightWhat's your problem?

Try this linkhttp://www.youtube.com/watch?v=IplgJRQHTJ4&feature=fvsr ... Dyson DC25 All Floors Bagless Upright Vacuum

My Dyson DC14 Animal doesn't have the suction it used to. The piece in the back on the bottom - a flap it appears - stays open now, causing the machine to make a louder noise than usual. At first, if I put my hand on the flap opening it would close, allowing for normal suction. Now, it stays "open" permanently", causing the loss of suction.

Hi its Darran at Dyson.Having had a look at a DC14 here, I am unsure as to the part you are referring to. So that we can help you further, please contact our Helpline free on 0800 298 0298, between the hours of 7am - 10pm, 7 days a week. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard

Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,

... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.

Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Suction Problem I took my unit to my work and used it, when I returned home it wouldn't suck up anything. I took the recovery take out and it has inward suction. Shouldn't that be outward, so it goes into the tank? It also blows out of the bottom by the brushes. I check the filter in the bottom and that is fine. Is it possible that it is somehow reversed the direction of the air flow (rotor running backwards)? I am perplexed. What am I missing?

There is a stand pipe seal where the bucket sits on, and if it isn't there or out of place could cause a suction problem like you said yours is doing. In the picture it is #10. The motor seal may have gone bad and is leaking # 15.\015\012 ... Hoover F7220900 SteamVac V2 Upright Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

I have a new bissell 50c9 upright vacuum and it keeps clogging in the clear window in the back. there is a flap that keeps coming open and filling up. everytime i clean and restart, the flap opens. i tried holding it closed and noticed lose of suction.

... Vacuums

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Canister problem When I lift the canister off to empty it, the flap at the bottom swings open, depositing 3 dog's worth of hair on my foot! The flap won't stay closed - even after I cleaned off the seal. HELP ME! Please.

Check that the plastic piece isn't broken. I had to replace my canister once because the little detent where the clip holds the base down was bent out of shape. It's too fragile to bend...just replace it. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?

Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?

Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.

Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.

You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

Hi.My model 116 36933502 only works as suction hose. When I use the bottom, a loud "flapping" noise and no suction. Everything is clean. Seems like a broken diphragm or filter? Sears Kenmore Progressive Bagless Intelliclean 5 years. Thanks Kate

... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

We have lost the manual for your Model 75224 can opener. This belongs to my elderly aunt who complains that she can't use it now because the handle was taken off and she can't get it back on. I recall this problem once before, and after looking at the picture in the manual, it was a cinch to put back on. Without the manual, however, I am having no luck.

I entered a search on Google, and I saw several pictures of the Can opener-- would just seeing a picture help?If not-- here is a site that claims to offer the manuals-- You will have to register, and dig into it a bit-- ... Vacuums

Hi we seem to have a problem with our Sebo .When in use as you draw the hoover back and forth seems to become very heavy to push as if the suction is becoming stronger. PLease can you advise. Mary

As you know, your Sebo automatically adjusts its brush height according to the type of floor it's on. At the correct brush height, on carpet, the machine should almost pull itself forwards. If this is not happening, the first thing to check is to loo ... Sebo X4 Bagged Upright Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu

Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

I bought a used Hoover Reind and there are two issues:1) There is no suction. The debris flies out of the back of the machine and 2) The machine will not shut off. You have to unplug it in order to get it to stop working. Any suggestions on either problem?

... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?

If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum

Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.

You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums

I have a model s3765 Hoover Windtunnel and it was no longer suctioning like it used to. I wanted to see if something was stuck in the rollers. I undid the screws at the base 3 of them and now I see there is a pic that do not undo these screws. I am having problems with getting them back in.

If you can post a pic of which 3 screws you are talking about and where you took them out of i can help u get it back together ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.5041 seconds