Having problems with your Dyson DC25 Animal Bagless Upright Vacuum ?

Where can i locate a anchor for a dc25 animal brush roll?

\015 I need to get the anchor that holds the brush roll in place. Not the side that has the bearing but the other side where the brush roll actually slides onto.\015

Answers :

Try the link below i think they only sell the complete unit with the motor
Repair Help & Product Troubleshooting for Dyson DC25 Animal Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where can i locate a anchor for a dc25 animal brush roll?

Try the link below i think they only sell the complete unit with the motorhttp://www.dysonpartsdirect.co.uk/dysonparts/dc25parts.shtml ... Dyson DC25 Animal Bagless Upright Vacuum

Replace dyson 07 animal brush roll assembley

The end caps of the brush assembly which contain the bearings are only a push fit onto the spindle (quite tight). Remove these and the brush bar will pass through the drive belt loop. To achieve this the belt has to be stretched slightly so care has ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The plastic drive for the roller brush on our dc25 animal is stripped out.it screws onto the motor shaft.does this part come with a replacement roller brush?

... Dyson DC25 All Floors Bagless Upright Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Dc25 animal. front brush not working

Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Once you've checked the cleaner head is free of obstructions and removed any threads or hair from around the brushbar, you should be able to reset ... Dyson DC25 Animal Bagless Upright Vacuum

Dyson DC25 animal brush doesn't spin

... Dyson Vacuums

I believe the clutch on my dyson "animal" is stuck. It makes this horrible noise when you try to lower the brush roll to vacuum.

Hi its Darran at Dyson. \012\012Your machine is designed to make this ratchet noise if the brush bar is \012obstructed. We would recommend checking the brush bar and soleplate \012area and removing any blockages or hairs/threads that are ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My brush has quite rolling. I have fixed it before, but it was a long time ago and I don't remember what I did. I can't seem to find the answer anywhere on line today. I have the Animal.

Sounds like the brush is stuck and/or the drive belt is broken or loose.\015\012You can find the manual to fix these problems here:\015\012\015\012http://www.dysonmedic.com/PDF%20docs/dyson_dc07_owners_manual.pdf ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc 25 animal brush not rotating - Dyson DC25 All Floors Bagless Upright Vacuum

... Dyson DC25 All Floors Bagless Upright Vacuum

The carpet brush on my DC25 Dyson Ball Animal has stopped working. Is there a reset button ?

Next to the power switch is another button, this switches the brushbar on and off. The brushbar can be turned off for hard floor surfaces so as not to scratch them ... Dyson Ball DC24 Bagless Upright Vacuum

Brushes do not spin - Dyson DC25 Animal Bagless Upright Vacuum

... Dyson DC25 Animal Bagless Upright Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush rolls of my Euro-Pro Shark vacuum (model-UV 210CN) are stuck; the brush is unable to roll. Does that mean I have to the roll on one end or the whole brush unit? I live in Canada and if possible let me know where I can find a store. Thank you.

... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

My Dyson DC25 Animal vacuum head is not staying flat after pushing Red Release Bar.

... Vacuums

Brush roll won't turn on for the shark NV22L vacuum. the light on the brush roll is dark, not red or green

Atthe bottom of the vacuuam are screws to take off...two of them are near the rear wheel assembly....two of them are behind the front mini wheels (just pry the front mini wheels so that they pop out...they pop back in)Remove all of the screws. Re ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Brushes stop rolling when against carpet, yes it is out of the upright position and when I left the base off the carpet the brushes start to roll again. What is wrong?

Your belt is stretched out so it just stops when the carpet resists it. Get a new belt made for your particular machine and you should be back up and running ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson DC25 animal motor not working

Hi there,I'm sorry to hear you're having difficulty with your DC25 Animal. If you haven't already contacted our customer Helpline, I'd encourage you to do so - you can reach us on 0800 298 0298 (UK), or 1-866-693-9766 (US). If a repair is nec ... Dyson DC25 Animal Bagless Upright Vacuum

Dyson DC25 animal motor not working

... Dyson DC25 Animal Bagless Upright Vacuum

Brush roll i am trying to find and purchase a new brush roll for my ge vacuum. The number on it says that it is 106585 and from what I can tell that is the same as 5550 parts. Is that correct?Thank you

I have the same vacuum for the last 5 years.  I dont know if its the same as 5550 (I assume it isn't) but I can give you the part number 61445-1.  It costs around $16 and you can call 1-877-207-0923 b/w 7 am and 8 pm Mon-Fri central time, o ... GE 106585 Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?

I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

The brush stopped on our DC25. Husband said sparks were coming out of the bottom near where brush is. Brush was cleaned of hair and string. Brush still does not spin. I saw no belt on the brush. Should there be one?

... Dyson DC25 Animal Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0720 seconds