Having problems with your Dyson DC25 Animal Bagless Upright Vacuum ?

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?

Answers :

Repair Help & Product Troubleshooting for Dyson DC25 Animal Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?

... Dyson DC25 Animal Bagless Upright Vacuum

My Dyson DC25 got stuck and wouldn't return to the upright position, I figured out that one side had jumped the track and gotten stuck in the square hole below the track. I did not want to break the plastic to force it back, so I removed the screw on the right side that was holding the kick stand on and removed the kick stand, also a spring thing came out. Problem is, now I have no idea how to re-install the kickstand. Can't find a technical manual or video anywhere, it can't be very difficul

... Dyson DC25 All Floors Bagless Upright Vacuum

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.

... Panasonic Kenmore Canister Vacuum Vacuum


Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.

I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I need a Dyson DC 17 Total Clean exploded parts diagream that shows the switch assembly. There are two small springs and a small plastic part that were loose inside the switch assembly. This caused the vacuum to shut off in the full upright position which is the position you use when using the wand.

I don't have a full diagram for you, but I do have a photo of how they are meant to be assembled: ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o

Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My dc 25 stabilizer bar came apart and a spring came out. Its on the right side. I need to know where it goes back in.

... Dyson DC25 All Floors Bagless Upright Vacuum

Can't get my Miele Power Brush SEB 236 Back together. Height adjustment mainly. Not sure where 1 loose spring goes either and which screws go where. Got it back together and had 3 left, then a 4th fell out when I vacuumed.

... Kenmore Vacuums

Hoover windtunnel tilt mechanism won't remain locked in upright position or at any of the fixed angle positions - now any slight bump and the lock releases. Normally you must manually use the small foot pedal release on the left side as you face the vacuum from behind.

Hello, stanI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Hoover floormate Hi, I'm not sure what the model number is on my Hoover Floormate, but I can't get the cleaning liquid to dispense. The vacuum(dry pickup works fine). The handle squeezes without a problem. It used to work without a problem and then I didn't use it for awhile. When I came back to it, it wasn't working. Thanks, Alissa

The tank sits on what is called the reservior asm. it is actuated by the control rod inside the handle. With the tank off, watch and see if you can see that rod hitting the reservior asm when you squeeze the trigger. If it is moving up and down on ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My daughter pulled to hard on the ceiling fan pulling out the chain. i have taken it off and apart, nothing appears to be broken but im trying to figure out how to put it together so it retracks, i assume it has something to do with the tension of the small spring inside of it, but not sure how to put it back together im wondering if there is a internal diagram of this ???

Don't even bother to repair the pull chain switch, get a new one at KMart, HomeDepot or similar store for less than $2.\012\012Two times I've repaired one, it comes apart when I need it the most.\012\012Good Day! Don't forget to rate thi ... Vacuums

My dyson DC17 will not turn on unless the handle is pulled back.(into the vacuuming position) The attachment hose will not work at all (0 suction thru it). I've checked the hose and made sure there is no obstruction. Any ideas?

Not sure if I can help, but I'll try. The DC17 has two motors: the vacuum motor and a separate motor for the brush bar. It is normal that the brush motor works only when the handle is pulled back in the vacuuming position - that's the way it's made. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Oreck vacuum cleaner will only stay on in the upright position. If I try to recline it to vacuum, it shuts off...put it back up and it turns back on. Of course I can't vacuum in the upright position...what do I do?

It sound as if you have a short in the cord or it has come loose from the motor you can take it part by removing the four screws in the buttom of the base plate to see if any of the wires are loose. ... Oreck Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.

You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing ou ... Kirby G6 Bagged Upright Vacuum

This dyson dc15 is pulling to one side not sure what it could be, also the wheels at the back dont seem to be staying down the are flipping back up when trying to stand it up, can anybody advise what

Look at the guide ... Vacuums

My 9 year old Sebo X4 will not stay in the upright position. The foot pedal no longer springs back to hold the machine in the upright position. Has a spring broken? Which part needs replacing?

... Sebo X4 Bagged Upright Vacuum

2001 kirby G6 vacuum wheel fell off. where does the spring go when put back together?

Here are some diagrams that may help you of the G6http://www.vacpartswarehouse.com/Kirby-Generation-VI-G6-Upright-Vacuum-Cleaner-s/ ... Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430

Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.

I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

I have a sta rite (pentair) cristal high rate sand filter model T-200-BP-1....its leaking water thru the top of the valve, where the valve cover screws on the valve body assembly. it leaks water out where they go together around the screws. Also when i vacuum it, everything that i vacuum gets washed back in the pool when its on the filter position. Also the backwash leaks when its turned 2 the filter position, does it supposed to do that?...the only way i have gotten it to stop is to put a seper

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1635 seconds