Having problems with your Dyson Dc25 Animal Ball Vacuum Cleaner - Excellent Clean ?

My ball has stopped going round and it looks like the filter in side it has moved, I can't push the Hoover at all

Answers :

Repair Help & Product Troubleshooting for Dyson Dc25 Animal Ball Vacuum Cleaner - Excellent Clean

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My ball has stopped going round and it looks like the filter in side it has moved, I can't push the Hoover at all

... Dyson Dc25 Animal Ball Vacuum Cleaner - Excellent Clean

Hoover U5344-950 My Hoover vacuum is a nightmare! I have had nothing but problems with it since day 1. The powerhead stops working if you try to lower the handle to vacuum. I took it in to be serviced and was told it sat on the shelf for too long in the store and it warped the belt...so it was replaced. Got it home, it worked the first time I tried it, then went right back to no powerhead working and as a bonus it is giving off a nasty smell like it is going to blow up! It now gets really hot to

... Hoover U5344-900 WidePath Vacuum

The beater bar doesn't move when you push the vacuum. If you lift the vacuum while it's running, it's going like crazy!

Replace the belt, it is so stretched that it is slipping on the beater bar when it comes in contact with the carpet. it takes the 38528-040 belt. i think its 5 screws on the bottom to gain access to beater bar and belt. ... Hoover U5262-900 / U5260-900 / U5266-900 / U5268-900 EmPower Bagless Upright Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st

Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet

I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac

There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

Stopped working Was working fine then it smelled like burning rubber, not the belt I checked. It sounds like the motor wants to run then it just stopped but the light is on. What do you think, go by a new one?? This has been a great vacuum cleaner and I can not seem to find a Sharp anywere. Thanks for your time.

Well it could be the motor, if it is it would cost around $80 or so for a motor. May be better to buy new, thre are a number of good brands out there. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My Jacuzzi Tracker 4x just "stopped"..there is a nice strong flow of water going into it, but the wheels just aren't turning. I've tried the following to no avail: 1. blocked suction for a few seconds underwater with my hand (this has worked in past) 2. try to move front wheels back and forth (but they won't budge...back wheels do move on track though) Should I start taking it apart?

... Vacuums

My Vacuum just stop working. I was cleaning my car carpets when it just went off. I tough it got disconnected from the outlet (power supply). The vacuum was connected and it is like when a fuse go bad, just like that it won't turn on anymore. Is there a switch that needs to be reset or a fuse to be replace? How do you do it?? Thanks

There is not any of that. Buy a new one ... Hoover Empower Bagless Upright Vacuum

We have a Hoover Tempo, and the brush stopped moving around. How do you get the brush to move again?

The most probable problem is the belt that runs the brush broke. Purchase a new belt for that model and replace. ... Hoover Vacuums

George i have just bought George from a friend and he has never used the wet side of things . When i turned the hoover on i cant seem to get the wet button to work. Do i have to have the hoover main button on first and then press the wet button?

The pump can seize up if the the system is not flushed with clean water after using carpet shampoo. You should run half a tank of clean water through Geroge before putting him away.The only solution is a new pump or pump motor. ... Numatic GVE370 Canister Wet/Dry Vacuum

Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still

This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My roomba spins and moves back and after 2-3 minutes stops and makes the uh oh sound followed by 10-12 beeps I cant say Im sure how many. Some days before stopped cleaning and told me to remove and clean the brushes I did that but then had this problem

\015\012\015\012\015\012\015\012Your bump sensors are malfunctioning. I had the same problem.. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. I'd recommend it. ... iRobot Roomba 530 Robotic Vacuum

The rollerbar keeps going on and off, depending on if you push it to one side or straight. If you push it straight it does not want to work and cuts off. the vacume is still on but the rollerbar does not spin

It could be that the belt is very worn or stretched to the point that it can't turn the brush against the carpet. If thats the case you can get replacement belts and view the manual here: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a hoover light & soft upright sweeper. In replacing the belt a "v"metal clip popped out. It is metal in a shape a "v" with one hole on one side and jagged edges on the other side. Where does it go and how to re-install it????

Its actually for your height adjustment, take off head again and you will see in middle there is alittle grove that fits that piece precisely..let us know ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.

Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

Loose wire ive got a loose wire inside my vax cyclonic 1700w and ive stripped it down but cant see anything and its still not working but it was working when i moved the wire from side to side. Please help

Sounds to me like you have a open wire. There is a break in the wire inside to the insulation and as you move it, it gains and loses connection. You can test it with a continuity tester as you move the wire or just replace it to see if that solves th ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall

That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us

Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums

Floormate noise Floorscrubber is only 6 mo old. It is making a grinding noise. Sounds like popcorn at times. I don't know why? It still cleans but the noise sounds like it is going to stop at any time.

The motor sounds bad. Use the Hoover web site to locate a shop near you for warranty repair. hoover.com ... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

How do I install brushes on Hoover V2 Windtunnel? Does a right and left go on the right side and vice versa on the left side? That is how it orignally came? Or do I put both rights on the right and both lefts on the left? Thanks for your help and advice.

Both right with right left with left. ... Hoover U8122-900 WindTunnel V2 Bagged Upright Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0886 seconds