Having problems with your Dyson DC25 Vacuum ?

Dc25 brush bar stops turning when placed on floor. Turns freely otherwise


Answers :

Repair Help & Product Troubleshooting for Dyson DC25 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dc25 brush bar stops turning when placed on floor. Turns freely otherwise


... Dyson DC25 Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The beater bar on my dyson DC28 is not turning when it is placed on the carpet. If you lift the sweeper up the beater bar will turn but then when you place it back down on the floor it stops.


... Dyson DC28 Animal Bagless Upright Vacuum

Brush bar not turning; vacuum cleaner otherwise has suction and works ok. No hair or other objects locking it/bar turns freely when not on


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Dyson dc25 brush bar not turning - Dyson DC25 Ball All-Floors Upright Vacuum Cleaner


... Dyson DC25 Ball All-Floors Upright Vacuum Cleaner

Brush will not stop moving when put in upright or bar floor mode. Also red power light doesn't come on when turned on.


Hi Chris,I'm sorry to hear you're having difficulties with your DC28. I'd encourage you to get in touch with us directly, so we can provide further assistance in resolving this issue. Please call our Helpline free on 1-866-693-9766 - or if yo ... Dyson DC28 Animal Bagless Upright Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

The brush bar on my Dyson DC17 stopped turning.


If this model has a brush control - i.e a roller at the side of the model which controls brush to spin or not, then its a protected brush model - therefore even if the drive belt is intact the Dyson would have to be repaired by a service personnel or ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush Bar Randomly Stops Turning


... Dyson DC28 Animal Bagless Upright Vacuum

My brush bar won't turn - works in bare floor mode, but carpet brush won't turn when it should...


Replace the belt the belt sounds like its worn or stretched the belts turn at high rpms and get very hot and soon just ware out they work fine on floors but when it comes to carpet they slow down, i hope this works out thanks ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The rotating brush bar won't turn after i cleaned all the tangled hair and string off of t ,... I don't think i positioned the brush bar back in to the correct place that will connect ,,can you PLEASE help me?


Hello pmoongoddess. Here is a list of dyson vacuums with the parts diagrams for each one. Find your model and then open up that parts diagram showing the rotating brush component. It will show you exactly how it is positioned. I hope this helps. ... Dyson Vacuums

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.


Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

The brush won't stop when selecting hard floor


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Can I use my ultra lix 2000 to vaccum my new ceramic tile and wood floors? It so how do you stop the beater brushes from turning so that they do not scratch the floor?


Yes you can, just set the height at maximum. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Dc25 brush bar head won't lay flat - Dyson DC25 All Floors Bagless Upright Vacuum


... Dyson DC25 All Floors Bagless Upright Vacuum

Have a bissell easy vac 3130-B and the brush on the bottom stopped turning i never looked before so i don really know if it turned in the first place


Behind the brush will be a metal thing that spins when the vacuum runs. That's what the belt loops over with the other end around the brush. You can sometimes find the belts a places like wal mart. ... Vacuums

I would like to vaccum my new ceramic tile and wood floors with my ulta lux 2000 how do you get the beater brush to stop turning so that it will not scratch the floors?


There should be an on/off switch on the right top of the power nozzle. If it's been running, then flip the switch. ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I was vacuuming over some fringe and then the brush just stopped working and there is nothing caught in it. It spins freely when twisted by hand, but will not turn when vacuum turned on.


Have you checked the belt? it could have snapped when you caught the fringe. also if it has a separate brushroll motor there should be a reset that probably tripped out. ... Vacuums

The roll brush will not turn when on floor. Too much pressure stops brush. Changed belts and still not working


Turn the belt inside out. This problem stems from a design flaw in the mechanism that turns the hoover from bare floor to carpet. After taking it apart I realized that the spring that pushes the belt tight (to make roller spin) is not any where nea ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.


I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??


... Oreck XL Ultra Bagged Upright Vacuum

I have the Eureka 4870 "The Boss" Smart Vac. The beater bar began to turn constantly and can't be shut by moving the Brush Roll Contol to Bare Floor position or the machine to the upright postion. It has also eaten two new belts. A local tech says he has seen this problem whereby the free-wheel assembly that makes contact with the belt to engage the beater bar is misalgned and cannot disengage. It is usually the chassis which would mean replacement of enough parts that would not be worthwhile


... Eureka Smartvac 4870 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1170 seconds