Having problems with your Dyson DC25 Vacuum ?

I just had installed a high pile carpet. I don't see and adjustment for carpet .


Answers :

Repair Help & Product Troubleshooting for Dyson DC25 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I just had installed a high pile carpet. I don't see and adjustment for carpet .


... Dyson DC25 Vacuum

Is there an adjustment on Dyson for high-low pile. Nothing cleans better but I'm handicap & can't push or pull Animal Dyson vacume over high pile carpet.


Yes there is an adjustment called a power cam. I am enclosing a link to show you exactly where it is\015\012\015\012http://www.dyson.com/homepage.asp ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson 28 airmuscle... carpet level selectors will not stop blinking... I have tried all selectors to see if an adjustment helps It has not lost section but the blinking light tells me something is up... I have two vaccumes one for upstairs and one for downstairs. all same carpet in the house and I use the medium pile and only one of the vaccumes is having this problem


... Dyson Vacuums

Trouble using Dyson DC07 on high pile carpets


... Dyson DC07 Bagless Upright Cyclonic Vacuum

On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.


I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

When i set it on carpet instead of bare floor it is hard to push when i vacume (when i turn nob it only has two settings floor and carpet no high pile or low pile)


Hi there,Sorry to hear you're having difficulties using your DC14 on this particular carpet. You may want to contact your carpet manufacturer to check it's suitable for cleaning with a vacuum cleaner equipped with a revolving brush. Manuf ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Dirt devile featherlite vacuum pushes extremely hard on high pile carpeting


The dirt devil featherlight has a automatic height adjustment for carpet and bare floors.check the wheels and see if there is something wrapped up around the wheels ... Vacuums

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?


... Dyson "Stowaway" Canister Vacuum Vacuum

Sanitaire commercial vacuum On some carpets, we can't get the correct height adjustment. It's either too low, so the beaters stall and don't spin, or so high that it fails to pick up animal hair. I'm not sure if something is malfunctioning or if I need to have a better understanding of how to adjust


... Electrolux Eureka SC689 Sanitaire Commercial Lightweight Bagless Upright Vacuum 14lbs

Dyson DC07 will hardly push over new low pile thick carpet. Too much suction. Any adjustments


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel vacuum cleaner and new high pile carpet. The vacuum cleaner will not move forward without extreme effort. I have been told that I need a vacuum without a beater bar and that the beater bar can be disengaged. How do I accomplish that? Thanks


You can adjust the height on some vacumes like for bare floors and medium nap it will adjust how far the beater bar is from the carpet see if your is adjustable ... Vacuums

New carpet has high pile and vacuum won't go forward on it


... Dyson DC21 Bagless Canister Cyclonic Vacuum

Folks, My wife and I own a three-year-old Hoover U6434-900 self-propelled "Wind Tunnel" upright vacuum cleaner. The problem is that, even on the highest setting (front-end as high as possible), it gets bogged-down in even shallow pile carpet to the point that the brush stops. I've cleaned the machine thoroughly, pulling hair, thread, dental floss and such from the brush (and everywhere else), including unscrewing the brush end caps and pulling out the cat hair mats which formed in there.


Check to see if the V belt sits too deep in the brushroll groove, if it sits too deep you will need to replace the brushroll. the top of the belt should be about flush with the brushroll. also you have to take the screws out of the self propelled uni ... Vacuums

We have a bissell and it the one to clean the carpet how do we use it i no to put hot tap water and turn it on and hold the grey thing to make the soap come out but nothing is picking up well i dont see nothing


Take this link to Bissel website, select your model and download yor free operation manual.\015\012\015\012http://www.bissell.com/ ... Vacuums

I need to change a belt and cant remove the casing as carpet adjust is attached and cant see how the red knob is removed


... VAX Appliances Vax X3 Bagless Upright Vacuum

My Hoover Wind Tunnel Supreme Model U5468 900 does not adjust up and down to clean hard floors or long pile carpets. The slide handle can be moved back and forth but nothing happens.


Something most have broke, you will need to take the top cover off and check it over. Maybe this picture will help.\015\012\015\012 ... Vacuums

We have a Dyson DC28. The brush no longer turns while vacumming the carpets. Also, the lights on the handle to adjust for different heights do not work. Can you help. I see of no way to get to the belt but I don't think it is broken.


Hi there,I'm sorry to hear you're having difficulties with your DC28. It's probably best if you get in touch with us directly so we can resolve this issue for you as quickly as possible. If a repair is necessary, this should be covered by our ... Dyson DC28 Animal Bagless Upright Vacuum

We have two of these vacuums and both of them have experienced the same problems. First the floor heighth adjustment doesn't work and now neither one will pick up on either carpet or floor when in the brush/floor mode. They both seem to work with the suction hose function. We have removed the back panel to see if there was an obstruction but it was clear. We have changed the bag and the small filter (not the HEPA filter) all to no avail. What else can we do? We are desperate to use our vacu


Did you check the powerhead for obstructions? With a bend in the tube just below where the hose connects, this is a common spot for clogs. To check, detach hose and drop a coin in the hole. If it doesn't drop through, a blockage is present. Use t ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

Canister powerhead brush does not seem to spin when the carpet level adjustment is on any level other than "high". Could it be something as simple as needing a new belt and is there a difference in a regular belt as opposed to "whisper belt"?


The belt is worn/stretched to the point that it cannot take the load on low level setting due to more resistance against the carpet and there is also no signifagant difference between the two belts except for expecting a longer belt life from the whi ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Is it possible to adjust the head for a thinner carpet (right now it's on a setting that works for a thicker carpet, so it doesn't pick up anything on a thin carpet). Is it possible to adjust the head and if so how? Also, how do you wash the filter?


... Eureka 4700A Maxima Bagless Upright Vacuum

Brush bar not spinning when set to high or low on carpet


1) adjust the belt, see for broken or worn, and replace2)see for brushroller obstruction, and clean it and repair3) see if the brushroller without belt run smooth, otherwise repair and fix it.Lubricate.4)See if the motor run without load( ... Vacuums

I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?


The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums

I have the Dyson DC14 and its like it's not brushing the carpet anymore, The brush is spinning, but its like it isn't self adjusting to the carpet height? It still has suction, but doesn't make the same sound it used to when you'd start vacuuming. Its like it never adjusts anymore???


Hi its Darran at Dyson.It sounds as though the internal hose underneath the machine has twisted slightly. With the machine switched off, lay it on its side and look at the base. You should be able to see a small corrigated hose. Simply t ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0473 seconds