Having problems with your Dyson DC26 Bagless Canister Cyclonic Vacuum ?

Bottom plate screws

\015 Cannot uncrew bottom plate which holds one of the filters\015

Answers :

They don't unscrew they only turn 1/4 of a turn then pull open watch this video
Repair Help & Product Troubleshooting for Dyson DC26 Bagless Canister Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What size screws are needed for the bottom plate of a Hoover U5061-900, the screw part number is 012-21447121


Any coarse thread screw about 1/2" long will work. There's no real "threads" inside, its just cut when they put the screws in at the factory. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J


There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums

Bottom plate screws


They don't unscrew they only turn 1/4 of a turn then pull open watch this video ... Dyson DC26 Bagless Canister Cyclonic Vacuum

I have a Fuller FB80 and am unable to remove the bottom plate for cleaning. I can only find 2 screws holding it on, but I'm afraid to force it in case I might break the plastic.


... Fuller Brush FB80 Bagless Upright Vacuum

The self propell does not work... i turned it over and took off th bottom plate and can see where the cable is suppose to be attached to the drive system, but it is no longer atteached, so it came out or a piece of the vaccum broke as it seems to be alot of plastic.. i see a screw and the end of the cable is still there... But where does it attach and how do i do it.. i havent taken the complete houseing apart yet as i have never done that before and wasnt sure about all the scres and what not..


... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

How many screws are there on the electolux epic 2500 sr on the bottom plate to hold it on?


There should be 5 screws. ... Vacuums

Can't remove bottom plate to change broken belt on oreck xl instashield vacuum ...i think i removed required screws


... Oreck Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.


The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

How do I change the belt on a Sanitaire upright sc5815? There are no screws on the bottom plate, or latches as other models have.


... Eureka Sanitaire SC4570 Bagged Upright Vacuum

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.


Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do you replace a belt on the a Simplicity Synergy vaccuum? Removing the 2 screws on the bottom plate allows you to access the roller, but doesn't give you access to the drive motor. Any ideas?


... Simplicity 7850 Premier Bagged Canister Vacuum

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to remove brush roller bottom plate


Make and model ?????? ... Vacuums

How do you remove bottom plate of the shark navigator vacuum


... Shark Navigator Bagless Upright Vacuum

Cant get the bottom plate back onto my dyson upright DCO7i


You need to press hard and turn till they lock inhttp://www.youtube.com/watch?v=fN8k--LbuCs ... Vacuums

Trying to get bottom plate off Electrolux upright


Step 1: UNPLUG YOUR ELECTROLUX VACUUM CLEANER.\015\012This is definately a belt change that can get expensive if you break\015\012something. I do not like the idea of a regular person changing this\015\012belt. I've seen people crack th ... Electrolux Cascade 140 Bagged Upright Vacuum

How to remove bottom plate


You will need either a t15 or a t20 torx bit. you should find these at any hardware store. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

I have a Kenmore quick clean model 116.36724500 and the belt popped off so we took the bottom off and put the belt back on, but now cannot get the bottom floor plate back on! Please help! :( I have no


... Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!


Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

Need to replace belt on Eureka Powerline 12.0 vac. Screws look like Torx head or something on bottom of vac. Are those the screws that need to come out for changing? If so, what size do I need?


No, do not remove the torx head screws for a belt change. If there are any screws that need to be removed for the belt change, they will be phillips head. What is model # of vac?? ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0232 seconds