Having problems with your Dyson DC28 Animal Bagless Upright Vacuum ?

Handle won't release - locked in upright position


Answers :

Repair Help & Product Troubleshooting for Dyson DC28 Animal Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Handle won't release - locked in upright position


... Dyson DC28 Animal Bagless Upright Vacuum

Dirt devil model 08633 handle wont lock in upright position


... Dirt Devil Vacuums

Hoover windtunnel tilt mechanism won't remain locked in upright position or at any of the fixed angle positions - now any slight bump and the lock releases. Normally you must manually use the small foot pedal release on the left side as you face the vacuum from behind.


Hello, stanI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

Miele s7000 I clicked my upright into sitting position and accidently bumped the foot release knob. The body fell back and now I can not get it to click back into upright sitting position. Something is now in the way of it locking into place. This happened last year and it was under warranty. it no longer is and I would like to be able to fix it myself in the future. Can you help me? Thank you. Kacee in Oregon


... Vacuums

Handle wont go to upright position


The red pedal has slipped out of position. On both ends of the red pedal you'll see metal rods (the axel of the pedal). On one side you'll see the metal rod sits into a long groove, on the other side you'll see the metal rod sits into a round hole. T ... Dyson DC25 All Floors Bagless Upright Vacuum

I have a Dyson Animal DC 28. It vacuums fine on floor mode, but, when locked in the upright position it releases pressure though the little valve behind filter a. I have only had it for 2 weeks so I'm hoping the filters don't need to be cleaned this often! I would like to finish vacuuming without waiting 24hrs for the filters to dry.


Unfortunately with any bagless vacuum the filters do need to be cleaned or replaced very frequently for the vacuum to perform. But the good news is it sounds like you have a clog in the hose. remove the attachment hose as you would be using it and un ... Vacuums

Vacuum lock Vacuum will not go back into upright position. There is resistance as you raise the handle.


I just solved my own problem. I'm not much of a technical writer and I'm sure I don't know the proper terms but nonetheless...\015\012\015\012...When standing behind the vacuum, as if using it, just above the right rear wheel is a detach ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Handle on kirby will not lock in upright position


... Vacuums

I've used my brand new Dyson DC28 once and now the handle will not release from the upright position. What can I do?


Sorry to be blunt... SEND it back. It is rated poorly, -Consumer Reports - is expensive to repair and is not worth HALF the price.... REALLY - you have a valid excuse, send it back and get a Consumer Reports and check out the ratings....\015 ... Vacuums

My dyson dc 28 will not release from its upright position. It feels like something is locking it.


... Dyson DC28 Animal Bagless Upright Vacuum

Rotator brush not spinning. Handle is not in the locked upright position. Says it's beltless, so is this likely an interlock switch or drive motor problem ?


Hi, the brush roll will only spin when your handle is not in the locked upright position, once the handle goes upright - the brushroll de-activates ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position


This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue ... Hoover F5858-910 SteamVac Vacuum

The wand is locked in the extended position on my Dyson DC28 and I don't know how to release


... Dyson DC28 Animal Upright Vacuum New DC 28 Animal

Oreck XL vacuum will no longer lock in the upright position.


... Oreck XL Ultra Bagged Upright Vacuum

Bissell 3595 handle release pedal spring(?) missing


I just fixed this on my Bissell PowerForce model #6594 vacuum myself. Woo Hoo for me. :-)\015\012\015\012I called the local vacuum repair guy and he told me he'd repair it for me if I insisted but that since my machine only cost about $80 ... Bissell 3522 PowerForce Bagged Upright Vacuum

Handle release how do I fix the handle release? It is not in the correct position. It has come out of the unit part way and will not latch the handle in place.


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?


... Euro-Pro NV31 Infinity Vacuum

Need new handle release kenmore 401.39035900


... Vacuums

Dyson wont staND UPRIGHT


Hi its Darran at Dyson. So that we can help resolve this, please call our Helpline on 0800 298 0298. One of our advisors can through some simple checks with you which will hopefully resolve the problem. We look forward to hea ... Dyson DC25 All Floors Bagless Upright Vacuum

The handle remains in the upight position


Spray some sillicone spray or furniture polish spray at the bottom where the handle adjuster slider can be seen by tipping the cleaner forward. Its usually a plastic bar that should slide. It can become dirty over time or just need lubrication. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Yellow Dyson handle stuck in down position will not click upright


... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0487 seconds