Having problems with your Dyson DC28 Animal Bagless Upright Vacuum ?

The red light is blinking & I can't push the white buttons to set height & not sucking

\015 Not sucktion\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC28 Animal Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The red light is blinking & I can't push the white buttons to set height & not sucking

... Dyson DC28 Animal Bagless Upright Vacuum

I have a genie screw type garage-door opener. the fuse blew on the moter drive board , now the door only opens when you push the light button on the wall console ,will not go closed.green light blinks continually. when I power it up it jumps closed then nothing. It seems like the motor is not reversing.

... Genie Company Vacuums

The clean light on the Roomba 520 doesn't quit blinking even when it has been docked for hours, i checked all the plugs and i also pushed the spot button for 10 seconds. it is a a slow continual blink as if it is recharging continually. what is the problem.

Sounds like you didn't remove the batteries protective tape. If this isn't a new roomba, your problem may be the charging cycle. For a brief video of what to do click the link below.http://irobot-homesupport-en-eu.custhelp.com/app/answers ... iRobot Roomba 530 Robotic Vacuum

My roomba mounts up to the charger the light blinks red then after a time it goes green but when I dismount it and push the green button it immediately goes red. It doesn't beep or do anything. It is that the battery is not charging?

You have dead nimh (nickle metal hydride) batteries. You\012will need a replacement. You can test for this by removing the battery\012and holding the power button for 15 seconds. This will restart the\012charging cycle as if the battery were new. ... iRobot Roomba 560 Robotic Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?

This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu

Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums

Dyson upright can't push carpet height buttons

... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Hi, the main box where all the wires connect to the sensor has the power on, and i've just noticed the small box where you enter the code to set the alarm does not work, yet the buttons are illuminated, normally the led light displays to show the power but no led's are on, the buttons doesn't work to set the alarm. Can you please hepl, many thanks.

Difficult as you didn't say what the equipment is but it sounds like there is a problem with communication between the main box and the keypad box. Have someone check that all the wires in the keypad are connected and there is no break in one of the ... Vacuums

I have a Zenith ZD300 Dehumidifier. Bucket full light blinks. The water bucket was not completely full. Emptied the water bucket and re-inserted. The bucket full light continues to blink. The humidity setting LCD shows 1%. What is needs to be done to correct the problem?

... Vacuums

Height adjustment The height adjustment button on my upright is nonfunctional.  The Height is set closest to the floor and it makes it difficult to move on medium height carpet.

You'll have to turn the upright to its side to show the sole plate where the rolling brush is. Check where the front wheels are located and ensure there is no blockage obstructing the rotary dial. Sometimes the spring mechanisms can work themselves l ... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way

If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums

I have a DC24 dyson and it is not having suction without white button on canister pushed in.

Hi there, it's Jack at Dyson.I'm sorry to hear your DC24 doesn't seem to be working as well as it should be. The white button you've described is the suction relief valve - this helps protect the motor if the machine is used when blocked. ... Dyson Ball DC24 Bagless Upright Vacuum

I have a philips FC9222 vacuum cleaner. When i switched it on today all the lights came on but the motor did not start. all the lights are on and you cant adjust the power up or dow n using the button on the top. the whole thing just looks like it has frozen on. i would be grateful if anyone can help. thank you.

... Vacuums


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My shark vx3 vacumn has stopped running... i tried recharging it, but still no luck... i then put a new battery pack on it and tried recharging, still it won't run... the charge light, (green) is on, the three red lights come on and flash when i push the on button...what should i do next?? this unit is about 6 months old... help!!

... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

Why doesnt my rootcycle dyson **** up! belt ok, emptied regularly, the handle bit where it sucks is fine but not the rotating brush. it sucks up fluff but not light dirt and bits. changed white pipe underneath as it was split.

There is a removable cover on the bottom of some Dysons which is like a U-Bend. On occasion this is a likely spot for blockages. Also make sure that all of your filters have been cleaned. Locate your local Dyson Customer Service from ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My TDK Clock Radio for iPhone & iPod (ADS-6P) freezes when I use the power button for the radio feature or try to set the alarm using the radio. Also using the ipod or iphone dock doesn't work. I have no idea what has caused the issue. Turning it off and on again doesn't help - it is still completely frozen and unresponsive to buttons pushed on the applicance one it has frozen. Can you help? I was given this item as a gift so I do not have the reciept.

... Vacuums

Have Model 350A with Chime Model MC3. Door bell does not work. Light is on at the button outside so there is power there but when you push the button - no chime at the intercom system

... M&S Systems Vacuums

Dyson dc28 animal Red light and all 4 white lights on and vacuum not sucking.

In the very bottom in back, there is sometimes a hose that bends and stuff gets clogged. Others like canister type have this weird valve in them that gets clogged and won't open allowing air to canister. I don't know which one yours has, but I would ... Dyson Vacuums

I have a GE model #SCA1000HBB02. Recently the control buttons quit working. I thought maybe someone locked the controls but thats not the case. The display lights up shows the time but thats all. I unplugged it and then powered it back up the display comes up to set the time but the buttons will not allow. Any help would be appreciated. Thanks, Gary

Sorry but this is the vacuum area, your problem maybe the main board or a fuse. please go to the microwave forum. ... Vacuums

I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2

Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums

Delonghi Citiz Milk frother not working. After pressing button, red light comes on and heat starts, then after a few seconds red light starts to blink and nothing happens.

Please visit the link provided below :http://www.delonghi.com.au/support/instruction_manuals/EN265BAE_im.pdf ... DeLonghi Vacuums

Dyson dc28 blinking red light on power button

... Dyson DC28 Animal Vacuum

Bissell Spotbot Pet Model # 33N8A. "Hose" button is only one that works, and only intermittently.

... Bissell Vacuums

Please help with my Roomba 550. Green light is on, but it won't do anything when pushing the button.

... iRobot Roomba 560 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0532 seconds