Having problems with your Dyson DC28 Animal Bagless Upright Vacuum ?
Dyson dc28 will not self propel
\015 Beater brush turns but vacuum does not pull itsself\015
Repair Help & Product Troubleshooting for Dyson DC28 Animal Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Dyson dc28 will not self propel
... Dyson DC28 Animal Bagless Upright Vacuum
Help Our Dyson does not pull itself or self-propel, and you can't push it forward. ANy suggestions?
Dyson vacuums are not self propelled. and if you cannot push it on your carpet then the pile of your carpe is more than what the vacuum can handle. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
My Dyson Absolute has started making a loud noise and the has gotten progressively more difficult to push. I'm guessing the self-propel has stopped working. Is there a quick fix?
Hi its Darran at Dyson.Try making sure the brush bar is turning when in the vacuuming position. It is possible that the brush bar is obstructed which can cause your machine to make this noise. Check out our online help at www ... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum
Dyson DC 17: Used to self propel, now does not. Have disassembled and found nothing obvious wrong.
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?
This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum
Just put handle on windtunnel u6401-9rm and the self propelled switch will not flip into self propel mode. is there an adjustment on the self propel part?
When installing the handle on this machine, you must be sure the on/off switch and the self propel button are both in the OFF position. The actual switch inside must also be OFF, and the metal fitting on the end of the power drive cable should be bet ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
Hoover 6485-900 self propelled will not roll. Self propel switch seems flimsy and I can't tell if it's working. New vac used about five times. I can see a wire moving down near the rollers when I engage the self propel but the wheels don't turn. Thanks for any assistance you can provide.
Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?
... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
I have a Dirt Devil Vision self-propelled vacuum cleaner. Recently, the self-propelled feature is stuck in the backward mode, so it only goes backwards! I can get it to go forward if I push really hard (i guess it is good for a workout!). I try to turn off the propel feature completely, but it will not turn off. please help!
Hi, the problem you are having is going to be with the switch that controls the forwards and backwards settings so with this stuck in backwards their is no way you can get this turned off, the other problem is your not going to be able to replace thi ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
Hoover self-propelled wind tunnel doesn't self propel going backwards.
Your self propel cable sounds like you need to have an adjustment. reccomend a service shop repair. ... Hoover Vacuums
I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.
I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums
Just replaced the belts on my Hoover Windtunnel II self-propelled vacuum. The brushes are now turning ok, but the self propelled feature is not working. Squeals when when you lock it in the upright position.
Check the plastic part, which the the self propelled cable is attached to. (release the handle, tilt it back. You should be able to see the cable attached by a screw to a black plastic arm.) It is either broken or the cable is lose. ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
I have 2 Hoover Wind Tunnel-self propelled bagged vacuums-U6433-900 model.The roller bar does not agitate, the self propelled feature does not work and, in general, the vacuum is not performing well. I have replaced the roller bar, the v belt and the wide belt. The filters have been replaced and it has a new bag. I have had both of these since 2004 and they were fairly expensive $200 each) but if the repairs are prohibitive, I might as well get new vacuums. Suggestions? I just spent $100 for bel
The Hoover WindTunnel self propelled is a machine that we see in our retail stores (Vacuums Unlimited) constantly. The benefit of having a supposed "self-propelled" machine wears of quickly after the numerous time you will need to take this machine ... Hoover Vacuums
My oreck self propelled belt came off so I put it back on but it doesn't self propel and I smell burning.
... Oreck XL Ultra Bagged Upright Vacuum
Hoover U6637-960 the self propel is not not working. When lowering the handle it acts like it would like to work but the roller will not turn. appears to be something to do with the self propel part of the handle . took the screws aout but can not get it apart. Is there another belt of something in there?
This vac has 2 belts. If both self propel and roller not spinning then most likely it is the wide flat belt broken or off. 4 screws on the bottom should gain you access to the belt area. another issue for this model series is a worn pulley on the rol ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Hoover upright self-propelled drive vacuum cleaner u6331-93 will not self-propel
Here is a video how to fix ... Vacuums
Self propell doesn't work. Motor spins and belt burns, brushes do not turn. model Hoover self propelled u6425-900
May be a stripped sprocket/cog or snapped shaft. check and replace as needed. ... Hoover Vacuums
Self Propel The vacuum will not work in a self propelled mode.
Me again with more info. This happened to me and I solved it as described previously. More info here:There's a microswitch located where the hose attaches to the bottom section of the vacuum. If the hose is not completely inserted, th ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Self-propelled Hoover windtunnel (with bags) will not self-propel. Belts are all in order, but I am quite sure it has to do with the cable. How would I fix this and how does the end of the cable with a nut, connect?
This might help - go to following website and look for "troubleshooting" \015\012http://www.fixya.com/support/p40544-hoo ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
How to disassemble self propelled vacuum to repair level that turns on self propelled mechanism
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Hoover self-propelled self-propel not working. belts ok.
No suction on Windtunnel 6630-900. All belts work, brush turns, it just won't pick up anything. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Self-propelled Broken? Vacuum very hard to push. Self -propelled doesn't seem too be working. What can I do?
I have the same problem, found out there is a cable that is broken, I'm trying to figure out how to fix it. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Brush off dyson dc28 - Dyson DC28 Animal Bagless Upright Vacuum
... Dyson DC28 Animal Bagless Upright Vacuum
My self-propelled Heritage II Kirby vacuum is no long self-propelled.
Her2 was not self propelled ... Kirby Heritage II Vacuum
Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.
... Hoover U6485900 Bagged Upright Vacuum