Having problems with your Dyson DC28 Animal Bagless Upright Vacuum ?

Dyson dc25 BRUSH DOES NOT ALWAYS TURN ON WHEN IT SHOULD


Answers :

The brush roller may be jammed with animal hair. If so, it will have to be removed and cleaned
Repair Help & Product Troubleshooting for Dyson DC28 Animal Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc25 BRUSH DOES NOT ALWAYS TURN ON WHEN IT SHOULD


The brush roller may be jammed with animal hair. If so, it will have to be removed and cleaned ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson dc25 brush bar not turning - Dyson DC25 Ball All-Floors Upright Vacuum Cleaner


... Dyson DC25 Ball All-Floors Upright Vacuum Cleaner

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson dc25 off button won't turn off, brush button won't engage brushes


Hi ... did u get this fixed cos mine is the same hve to switch off on the wall? ... Dyson DC25 All Floors Bagless Upright Vacuum

When I turn my Dyson ball DC25 vacuum on and engage the brush it makes a screeching noise. I have cleaned the brush and the filters were cleaned a week ago and are in correctly.


Check if the belt still is connected and freely rotating the brush. Dyson vacuum belts are not replaceable.If the belt is going bad, the clutch assembly has to be replaced ... Dyson Vacuums

DC25 roller ball dyson brush won't turn


... Dyson DC25 All Floors Bagless Upright Vacuum

Dc 25 beater brushes not turning around - Dyson DC25 All Floors Bagless Upright Vacuum


Check the belt if thats ok then you will need to check the switch for the brushes ... Dyson DC25 All Floors Bagless Upright Vacuum

Brush wont turn on my dyson....only had for 4 months....what do I do with this piece of crap?!?!


... Dyson DC39 Animal Canister Vacuum

Non working roller brush on dyson dc25 vacuum cleaner


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson brush wont turn


Hi There is a reset switch on your Dyson that needs to be pressed when something gets stuck in the brushes. The reset switch helps protect the motor that spins the brush from damaging if something gets stuck inside the brushes. There is a little ... Dyson DC25 All Floors Bagless Upright Vacuum

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

Dyson DC21 brush will not turn on all the time. When the brush turns on, it won't turn off.


... Dyson Vacuums

Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan


I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum

My dyson DC25 brush button is stuck down - Dyson DC25 All Floors Bagless Upright Vacuum


... Dyson DC25 All Floors Bagless Upright Vacuum

I have the Dyson DC7 & the brush no longer turns. I just noticed that nothing is being drawn up & when I turned it over to see if I had a plug-up the brush was stationary.


You need to replace the belt. Here is a link to the belt you need and a manual you can view:Dyson DC07 Belt and Manual ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc25 roller bar won't turn


... Dyson DC25 All Floors Bagless Upright Vacuum

The brush bar on my Dyson DC17 stopped turning.


If this model has a brush control - i.e a roller at the side of the model which controls brush to spin or not, then its a protected brush model - therefore even if the drive belt is intact the Dyson would have to be repaired by a service personnel or ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Motorized brush bar not turning on Dyson Vacuum


Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the "control board" is located down into the hinge / ball area become stretched and then fray and eventually break. Ha ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Dyson DC07 Vaccum - brush will not turn


Hi.\015\012\015\012Your Dyson has A clutch unit this engages the brush roller when you pull the handle back to vacuum.Check the clutch control knob which is at the bottom left side of machine looking from the front. It s ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc25 brush bar switch


... Dyson DC25 All Floors Bagless Upright Vacuum

Dyson Stowaway carpet brush turning off randomly while vacuuming.


... Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum

Roller brush of my dyson dc07 isn't turning...


It migh be the belt.check your belt or it is the brushroll is stuck.(from to much hair ect.) ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!


Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0579 seconds