Having problems with your Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum ?

My dyson dc31 will not hold a charge and only runs for about two seconds then you have to release the trigger then it runs for another 2 seconds and so on.

\015 It stops every 2 seconds and will not charge beyond red. I have tried another battery but no change.\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson dc31 will not hold a charge and only runs for about two seconds then you have to release the trigger then it runs for another 2 seconds and so on.

... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

When squeezing trigger, vacuum runs for 10 seconds then stops.

... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

My DC 16 will only run for a second each trigger pull. The battery is fully charged, it has plenty of suction, just wont run for more than a second. I cleaned the filters.

I had the same problem with my Dyson DC16, where it only runs for a few seconds at a time with each trigger pull. My husband called Dyson (Canada) and without hassle they shipped us a replacement part which I just received this morning. The replace ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Nilfisk GD-2000. Same problem with the new vacuum as the old one, runs 30 seconds to a minute & shuts down. Sometimes it'll start & run another 30 seconds or so, but shuts down. Other times it won't start back up at all. No clogs & bag is new. Please help.

... Vacuums

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you

Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums


... Dyson Vacuums

Runs 10 - 20 seconds then quits-restarts on next trigger pull

Check battery maybe is old or not correctly charged. ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Runs for about 30 seconds then shuts off, runs for another 30 then shuts off...continues to do this

... Dyson DC31 Bagless Handheld Vacuum

I have a Model F7431-900 and is a SteamVac V2. When I press the trigger for water or cleaning solution, the water just runs right through it even after releasing the trigger. What kind of problem do I have? Is it most likely a valve problem? I'm handy at fixing things and want to avoid the large repair bill if I take it in.

This sounds like a stuck solenoid. The Dual V models use solenoids to contol soap and water flow to the floor, along with a pump unit. If your unit is 12 months or less it is under warranty. I am not sure about the cost of the solenoid. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Bissell Proheat model 8930 stops dispensing liquid after about 30-45 seconds when trigger is operated...occurs both with hose and upright modes. When shut down and restarted, dispensing resumes and again stops after another 30 seconds.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I need to change the retractable cord in a Kenmore Model 116.228.13204 vaccum but can't figure out how to remove the housing. I have removed the bag and the two screws but the top appears to be attached under the foot pedal. How do you release it. Does the foot release pop off somehow to reveal another screw in the back of the housing?

Go to this web site, it gives you complete schematics of your model. This will make it easier to see where all screws are and what you have to remove to get to reel. http://www.searspartsdirect.com/partsdirect Just enter your model # and complete bre ... Kenmore Vacuums

The Oreck vacuum motor sparks the stop running. Plugged to another outlet, the motor did the same things, run for few seconds with sparks and stopped again.

... Oreck XL2200 Bagged Upright Vacuum

Dyson My Dyson DC04 runs for a second or two then stops. I have checked the motor. The brushes are good but the commutator is a slightly pitted.Do I need a new motor?

Hi.\015\012\015\012Check mains lead where it enters machine very common for internal fracture.\015\012\015\012To prove this try waggling lead with machine switched on if it starts & stops this is the fault.\015\012 ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have two older Filter Queen (brown vacuum cleaners). Besides unclogging the hose area and making sure it is not filled with dirt, what else would cause the machine to run hot and have a high pitched sound? Is there another area where I might have clogs?

There is a secondary filter under the paper cone that gets filled with fine dust. It can choke off the airflow. The noise motor sounds like a bearing going dry. That should be replaced ... Filter Queen Majestic Canister Vacuum

Miele S318i worked ok till I took it apart to blow really fine ceiling "popcorn" dust that got sucked by the filters. When I plugged back in started for a milli second and quit. At this point I believe the circuit board might be the fault, but I want to test motor before I go and buy the part. Can I simply run 110 to the two moter contacts to bench test? Steve

Yes, you can. ... Miele S318 Bagged Canister Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.

How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

Not one, but two Bissell-Power Force Vacumns are defective. After assembling the first, it would not run. Bought another only to find out, it will not work either.

If these vacuums are less then 1 year old, they are under warranty, call the Bissell number and they can tell you where the nearest repair shop is. That along proof of purchase. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio

Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

My wife and I own 6 IRobots: 1 Scuba 1 Dirt Dog 4 House cleaning vacume models All of them are not working, so I decided to try and solve the problems with two of them: One is a dirt dog and the other a house cleaning vacume Rumba. Given: Battery is fully charged Reaction: I start both of them. They run for about 2 to 3 seconds They come to an abrupt stop as if there is a rock in the gears. Help

Both of them have identical issues? Can you please provide the actual part number of them? It should be on the bottom or inside the battery area somewhere.ThanksTim ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

Vacumn stops running after about one or two minutes then won't come on again for about 30 seconds.

The motor has thermal protection. If it heats up the protection turns it off. Then it won't start until it is cooled down. Check if anything is obstructing the path of the air. First on the suction side. Failing that it is possible, but tedious to ge ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Dyson Root 6 made a loud banging sound, and now its motor emits a strong burning smell every time it's switched on. It runs for a second or two, making a lot of noise, and then stops. (Just bought a new battery for it, too - what a drag...) It's off warranty, and Dyson wants almost as much to fix it as a new one would cost. Is my Root 6 e-waste, or is there anything that can be done for it?

... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

I have the same problem as steve967 The dyson dc16 is fully charged, runs well for 5-10 seconds and shuts down. I wait for a second or 2 and it runs again for 5-10 seconds. This will continue for numerous cycles, until I am finished cleaning. I have cleaned all the filters, and the power is good, The system will just not stay on. It is just over 2 years old. A friend of mine had the same problem with his Dyson DC16 after just a couple of months and has replaced his Dyson with a Black N De

Dear Michael_Stad,I am going to sound like a broken record but here is my same answer to another person with the same problem.I have I had the same problem with my Dyson DC16, where it only runs for a few\015\012seconds at a t ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

DC-16 battery vacuum runs for 10 seconds then cuts out. After waiting 30 seconds, it runs for about 10 seconds then cuts out again

... Dyson DC07 Bagless Upright Cyclonic Vacuum

New battery!, roomba runs for 5 - 10 seconds, stops, starts running, stops, runs, stops, then beeps and low battery flashes. Have taken battery out, held start button 20 seconds, replaced battery and directly connect to charger, 72 hours min., still same problem.

... iRobot Roomba Discovery SE Bagless Robotic Vacuum

On the DC07, the entire cyclone assembly must be removed to empty the dust, debris, etc. collected when vacuuming. On the top of the cyclone is a "trigger" that you lift with your finger to release the bottom catch, which allows a clear flap to open on the "clear bin," thus letting all the debris fall out. My problem is when you lift the finger trigger, it does not release the catch on the bottom. Since the catch won't release, I cannot remove the entire clear bin either from the cyclone.Any sug

Beofre you go to the extent of buying a replacement canister, you can remove the top and using a straightened coat hanger type thing open that bottom lid. Then maybe you can clean the rim and possibly add some silicone spry to loosen things up. Here' ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0511 seconds