Having problems with your Dyson DC33 Bagged Upright Vacuum ?

Carpet/hard floor selector not working on my dyson dc33

\015 Brush not turning when i vac the carpet. are the belts at fault or is it the selector?\015

Answers :

Repair Help & Product Troubleshooting for Dyson DC33 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Carpet/hard floor selector not working on my dyson dc33


... Dyson DC33 Bagged Upright Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My dyson seems to have lost its suction therefore is not picking up anything yet i have found that when my dyson is standing upright it has a little more suction but nothing like how it use to work. This has only happend in the last 2 weeks. I sanded a floor & though the sander picked up majority of the dust i did use the dyson to pick up the excess and it is since then that my dyson has not been working to its full potential.


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC07. You should be able to resolve the issue by following these simple steps: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson dc33 manual - Dyson Genuine Dc33 Stubborn Upright Multi-floor Vacuum Dyzolve Spot/c 3tools


... Dyson Genuine Dc33 Stubborn Upright Multi-floor Vacuum Dyzolve Spot/c 3tools

Dyson dc33 brush bar wont spin - Dyson DC33 Multi floor Upright Vacuum Cleaner Blue- Refurbished


... Dyson DC33 Multi floor Upright Vacuum Cleaner Blue- Refurbished

How to get a dyson DC33 blow outward - Dyson DC33 Multi-Floor Upright Vacuum Cleaner


... Dyson DC33 Multi-Floor Upright Vacuum Cleaner

Replace the belt in a dyson DC33 vaccum - Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner


... Dyson DC33 Multi-Floor Upright Bagless Vacuum Cleaner

I was vacuuming with my DC28 Animal and all fo a sudden the beater bar stopped working and NONE of the floor mode buttons work.. no lights or anyhting. I checked for obstructions per the Dyson manua


... Dyson DC28 Animal Bagless Upright Vacuum

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.


Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

My dyson dc17 animal will pick up via the hose attachment but there is no suction when you use the regular vaccuum on the floor - you can hear the difference in the suction once you put the floor part down - we took it apart - cleaned it - checked all hoses - still does not work????


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson cordless stopped working - Dyson DC35 Digitial Slim Multi floor cordless vacuum cleaner


... Dyson DC35 Digitial Slim Multi floor cordless vacuum cleaner

Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.


You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Beater bar not working. suction not working - Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum


Check for a broken beater brush belt.\015\012Clean the beater brush, clear of all debris and add some WD40 at each end where the rubber holders are. Turn beater brush by hand to work the WD40 into the axle.\015\012Reassemble making sure the belt is ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have Dyson DC15 ,Brush not working - Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum


... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Dyson dc41 floor suction stopped working


... Dyson Bagless Upright Vacuum DC41 Animal

Dyson DC14 bare floor adjustment knob not working


Clutch is broken needs a new clutch. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Dyson 39 Animal Canister vacuum that was working very well on my laminate wood floor. I have had for two months with no issue. Recently the suction is so strong that vacuum takes effort to m


... Dyson DC39 Animal Canister Vacuum

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Dyson slim upright has lost suction via the power head , floor wand is working normal


Its either the power head is clogged up with debree or the belt is broken. if the belt is broken it wont wisp everything up. Take it to a shop to fix. DONT TRY TO FIX IT YOURSELF~!!! dysons are very expensive and arent made to just be taken apart ... Dyson Vacuums

Carpet My Dyson Animal works fine on the ceramic tile floors, but hardly picks up anything from the carpeting. What is wrong?


Have a look at the brushes are they turning and if they are can you stop them turning if you tuch them with your hand??? if you can stop them turning the brush drive belt is slipping get a new belt and fit it,,\015\012problem sorted!!!! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My dyson 25 animal has lost suction from the floor portion of the machine. All the hot hair is coming off the front bottom part, by the ball. Its as if the connection of air has been disconnected. The attachment works fine, though.


You have a serious clog that must be removed. It is somewhere between the floor and the bag or where ever the dirt goes. Clear it and you will be back in business.\015\012\015\012Thanks for using fixya.com ... Vacuums

Why does my Dyson Animal Upright Vacuum power light turn red when I tilt it back to vacuum? It will work if I switch it to bare floors and don't need the beater brush.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson DC07: When I first got this vacuum, it was so powerful that it lifted my area rugs off the floor. It is so weak it barely works. I have removed and cleaned the filter, but I can?t seem to improve the suction. What am I doing wrong? How do I fix it?


Hello,\015\012\015\012If your vacuum runs but still leaves dirt behind, the culprit could be the drive belt or an obstruction. If the agitator brush slips or won't turn, the belt is bad and needs to be replaced. If suction is weak when yo ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0678 seconds