Having problems with your Dyson DC41 Animal Bagless Upright Vacuum Cleaner ?

My dyson 41 sucks the floor so hard it is hard to move or turn.Just started a couple of weeks ago


Answers :

Repair Help & Product Troubleshooting for Dyson DC41 Animal Bagless Upright Vacuum Cleaner

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson 41 sucks the floor so hard it is hard to move or turn.Just started a couple of weeks ago


... Dyson DC41 Animal Bagless Upright Vacuum Cleaner

Dyson My Dyson vacuum runs for a while and then quits. If I wait a few minutes it will start back up. This just started doing this a couple of weeks ago.


The automatic cut out switch on the motor needs replacing when the motor gets hot this switch comes in and stops the motor from overheating when the motor cools down the cleaner will work again and cut out again when the motor gets hot if it is not r ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and


Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.


This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson vacuum cleaner ...upright....all of a sudden my vacuum started making this awful sound...like a loud buzz...but only when I have it on carpet....when I have it on "floor" mode it's fine....sometimes(although seldom) it has worked without buzzing...and it's LOUD!!....I have only had this vacuum for a year....and no...I have never picked up any coins or hard stuff.only use it for 2 rooms.the rest of the house is wood floors.......what shall I do? Thanks......Gloria


It may just be, that on carbet the brushes make noise that you dont hear on woodfloors.\015\012If there is a hights adjustment, set it higher for shaggy carpet and lower for berber. ... Vacuums

My Dyson animal seems to have an electrical issue that I am unable to pinpoint. Neither the wand nor the floor vac have any suction AT ALL. In fact the vac makes absolutely no sound and you wouldn't even know that it had power to it unless the rollers are turned on, the rollers work just fine. I had this problem start about a month ago and then it just started working again after messing with it for a while, now it has happened again and I am getting a little agitated! Please Help!!!!!!!!!!!


There is a filter inside the canister, and by your description it sounds like it needs to be cleaned. if you remove the filter and blow it out using a air compressor or using a slightly ridged brush and tapping the filter out this should solve your ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson ball sucks fine while moving forward, when pulled backward it leaves hair or whatever on the floor. Works fine going forward????


... Vacuums

I have a fantom wildcat vacuum, and the filter is clean, and I see no other clogs. The vac sucks fine on hard floors, but the roller brush does not move. I can't even manually push it around. S


... Fantom Vacums Fantom Wildcat 2100 Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson dco7 it just recently started making a horribly load noise if i run it in carpet mode but not in hard floor mode what can i do?


Change the belt(s). Here are the belts you need:Dyson DC07 Belts ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a DC25 that I just bought in Dec 10. The last few times I vacuumed the carpet, the beater bar worked on and off. Now it does not move at all. I took off the beater bar to see if there were any obstructions, but there were none. Could you please help me with this. Right now my husband is saying that we should not have bought such an expensive vacuum (which he has said all along). I want to prove him wrong!! Up til a couple of weeks ago, it was working perfectly and I have loved it!


This is a good quality machine which I am sure wil last a long time in answer to your question make sure that the setting is set for carpet and not just flooring ..the head needs to be flat on the floor for the beater to work .I am assuming that thi ... Dyson DC25 All Floors Bagless Upright Vacuum

My Dyson has suddenly starting making this LOUD, horrible sound when I am using it on the carpet setting. However, when I use it on the floor setting, I do not get this noise. Also, I think the 'sucking' power is not as strong.


You need to check the beater bar on the bottom and the hose from the beater to the canister. You may have something stuck in the beater system. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Oreck xl commercial spits out dust on bare floor but work on carpet. It is about 15 years old. Bag has been changed. Brushes are spinning so belt is working. Started about 2 weeks ago. HELP!


It might be that the beater brush is spinning when you tip it up to look at it but slight pressure of it contacting the floor is enough to stop it.\015\012If it were my machine I would remove the beater brush and clean it as best I could, paying part ... Oreck XL Ultra Bagged Upright Vacuum

I have a new Dyson upright vacuum. The vacuum will not stay on. I used it a couple of hours ago with no problem, but now it won't stay on. It seems to be sucking and running normally otherwise. What can I do. Thank you. Donna Eakman


Hi Donna, My name is Don.\015\012\015\012When you say it wont stay on could you please advise the following:\015\012\015\0121. Does it cut out suddenly as you are using it?\015\0122. How long can you use it before it cut ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I bought Roomba 560 robot vacuum cleaner about 3 weeks ago and it has been cleaned without problem all kind of positions of floors (also carpets) Last friday I anyway mountained nearby of outcoming door the black carpet. Now the situation is that Roomba doesn't move and clean above of this carpet. What is the reason and how to solve it ... ?.


Ok, take regular WHITE paper. Do not press it on the sensor, just make it long enough so it covers the sensor. Then, take some clear tape, and tape the piece of white paper over it. Watch for the wall brush and stuff, don't get it to close to them or ... iRobot Roomba 560 Robotic Vacuum

Two weeks ago, my 4150 roomba stopped during running and sounds "ehh". every time i hit the clean button it sounds "ehh" and doe'snt work. at the first time it did it ,i have cleaned the sensors then it start moving forward and backward until it stopped . from now on it only sounds "ehh".


EHH sound:-------\015\012Cliff sensors are dirty or need repair.Try cleaning the sensors and check.If still the same problem then the sensors needs to be rechecked and its connections has to be replaced.\015\012You can try this opt ... iRobot 4150 Roomba Vacuum

I know this sounds like a dumb problem to have for a vacuum but our 6 year old dyson has so much suction you can't move it across the floor. It only recently started doing this and I haven't done anything to it such as clean the filters in over 6 months. Any help would be appreciated


... Dyson DC14 Telescope Reach All Floors Vacuum

I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My dyson seems to have lost its suction therefore is not picking up anything yet i have found that when my dyson is standing upright it has a little more suction but nothing like how it use to work. This has only happend in the last 2 weeks. I sanded a floor & though the sander picked up majority of the dust i did use the dyson to pick up the excess and it is since then that my dyson has not been working to its full potential.


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC07. You should be able to resolve the issue by following these simple steps: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I just got this euro pro shark steam mop. I dont have a manual for it so i dont know much about it. I put water in it and it heats up but when you start to use it. It makes a gurgling kind of sound and steam comes out, but not very much i dont think and on the floor you can't hardly tell where you went over the floor at cuz it's not very wet at all. So is it suppose to make a gurgling sound and should'nt the floor be alittle wetter?


Call Shark. They have good cust. support. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Brushes won't move on the floor but will move when they are picked up and moved to start


Sounds like the belt is heavily worn and slipping or has not properly been put on. Check the belt and reinstall or replace dependin on the condition. These will wear over time as well you have 2 belts and I would recommend replacing em both. One tu ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up


Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums

My Vacuum DC-17 has just quit sucking. It has been making quite a racket since I had the belt changed at a repair shop several months ago. I was told that the belt was a new design and figured that was why it was making so much noise. it seemed to work fine, was picking up dirt and all, but today, when I started vacumming, I noticed it was not sucking air either with the belt engaged or not. My vacuum is approx. 5 years old.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0702 seconds