Having problems with your Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum ?

Dyson clogs at main intake . Cleaned entire unit, it appears to work fine and within 15 minutes it is clogged again.


Answers :

Six months just stopped steaming. Don't wast your time trying to take apart.
I poured small amount of vinegar in and let it sit an hour then empty it out and ran a small wire into the base of the steamer. I could feel resistance but after poking it a few times it cleared! Put water in and it worked. On to the next project.
Check both of your filters they are probably clogged causing the other clog to occur
Repair Help & Product Troubleshooting for Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson clogs at main intake . Cleaned entire unit, it appears to work fine and within 15 minutes it is clogged again.


Six months just stopped steaming. Don't wast your time trying to take apart.I poured small amount of vinegar in and let it sit an hour then empty it out and ran a small wire into the base of the steamer. I could feel resistance but after poking i ... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery


Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I've tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That's what leads me to believe there is a clog. If you can help, please do. I like the product and haven't been able to use it for awhile because of this. Thanks.


I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rec ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators


Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums

The unit works fine for 10-15 minutes, then the power cuts off. If I let it rest for 15-20 minutes, sometime it starts right up again. The filters clean clean, the brushes are not restricted, the retainer is empty. ???? Tom Abbott


Hi, it is over heating due to insufficient air passing through the motor and a heat sensor is cutting out the power due to a blockage maybe a filter or a cloged hose.\015\012\015\012\015\012The ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

My vac's hose works but the main machine stops picking up dust and stuff after about a minute or so. Thn I have to take the hose of and clean the stuff from the main unit. My machine is 6 yrs. old


... Beam Industries 2775 Serenity Plus Central System Vacuum

I have had my RCA microwave model # RMW1108 for about 8 months now. It was working fine until yesturday evening. I went to warm up some food for 2 minutes, the microwave itself was on and everything appeared to be working except my food did not get warmed up. I plugged it out and checked all over it for any damage but i could not find anything wrong. What would cause it to just stop heating up the food? Is this type of problem covered in the 1 year manufacturer's warranty.


... Vacuums

Let's try this again. The main vacuum and hose works fine, the "foot" does not. When I turn it on, it shuts off automatically and the light comes on telling me to "check brushroll". I did this and removed all hair, strings, etc., Still won't work. Please respond. The last post took over 30 minutes with no response.


Sounds like you have hair or carpet buildup in the roller and it is not freely rotating and you are getting an error. If there is no buildup, then roller bearings may be frozen up, or the unit has a faulty capacitor and is not going to work due to el ... Vacuums

Hi, my Dyson DC16 works fine but after removing from charge base following recharge the red and green lights remain lit and the unit will not operate until i remove the battery and reconnect to vacuum,this extinguishes the lights and now can use with no problem.I guess that the charge control within the vacuum is not recognising that the unit has been removed from charge,is there a solution? Thanks


... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

I have a Bissell ProHeat 2X which releases the water/shampoo mix fine, and will suck up using the hose, but will not suck up using the main floor unit. Have checked it all out, and there do not appear to be any blockages. Help please


The vacuum on its back then look under the front where the water comes\015\012out, you will see few little round holes now the chances are these\015\012holes are blocked so get something long like a pin and poke these holes\015\012through you should ... Vacuums

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a


The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How can I get my DAB radio working again? I have a Sony XDRS100CD with DAB radio. The DAB radio has stopped working although I can still use the CD and get FM radio. The unit has a readout on the front that usually shows the time and this stopped working too, presumably because it got the time via the DAB radio. The unit works from mains and batteries although I have only ever used it on mains.


I have the same problem... did you ever get a fix..[email protected] ... Vacuums

The unit works well for 3~4 minutes and then stops. Wait another 10 minutes to cool down and it works again but the same issue happens again and again. It is a brand new unit. I read the manual for the thermal detector and did what it says but the issue is not resolved. Thoughts?


Hi, I have a Hoover Bagless myself. I also have worked professionally fixing Vacuum Cleaners. There may be some material caught between the roller end and the end bearing or the edge of the roller compartment. This could b ... Hoover UH70015 Bagless Upright Cyclonic Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My DC500 works fine running on battery power, but the motor hesitates for a moment or two when the unit is switched on with ac power. After this it works fine. What might be wrong?


May be the carbon brushes are short or motor connectors have become bad connection by moisture and dirt by use temporay a wrong filter sometimes its a very light and simple motor johnson motor with hammer brushes \012 ... Dewalt Vacuums

Dc35 pulsing Hi I have a DC35 it works fine until i put the main head on and then the motor starts pulsing and cuts out after about 10 secs. If i remove the main brush head it runs fine again ? Please HELP :)


Check for debris in the head and remove ... Dyson DC35 Handheld Vacuum

Model, 116.c85pbpk0v022 Power-Mate Jr. attachment stopped working, could it be a part within the unit (i.e. the electrical component) or do I need to replace the unit? How do I troubleshoot the electrical connection? No known drop or abuse. Worked last time I used it.


This model frequently stops because, lint, hair, etc. gets caught between the two end pieces of the brush cylinder. Do the following to fix it:1) Remove the two Philips screws from the underside of the unit. 2) The side with the tag will ... Kenmore Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

Centralux - unit will operate for 10-15 minutes then shut down. We hit the reset button, unit operates for 20 minutes then shut down again. Had customer svc stop by, they checked the hose, filter, no clogs, etc. ANy ideas


Check the screen. It's located underneath the motor. You can see if it's clogged by removing the filter and with a flashlight look up at the bottom of the motor. If it is clogged, the easiest way to clean it is unplug the vacuum, disconnect the two m ... Electrolux Centralux Vacuum

My wife has a Revlon Rv051 curling iron .. has worked fine for several years but now it has stopped working. No response to pushing the ON switch (normally turns on a red LED). I've opened the unit and verified the integrity of the cord and swivel contact between the cord and the PC card. Unfortunately w/o any documentation of the PC card, I'm at a loss as to what to try next. My wife has had this unit for several years ... liked it well enough that she now has two more of the same model but


Is power making it to the switch? Sometimes the plug of the unit with pushbuttons has issues and fails. Maybe you can switch a plug from 1 of the other ones you have to test. ... Vacuums

Just purchased the unit 2 weeks ago. Worked great. Last night I left it plugged into an outlet - but turned "off". This AM the unit comes on; timer showing default @ 5 minutes; however, no "bubbling" action. Would leaving the unit plugged into a surge protector/UPS back-up unit overnight damage the product?


I wonder if you are talking about a coffee maker? It ended up being listed under Vacuums!-Sorry about that-- It sounds like you arehaving trouble getting the maker to boil water, and move it thru the maker, no?Anyway-- I don ... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

My bissell powersteamer model 1695 does not spray enough water out. Hardly anything will come out of the handheld attachment either, just a few drips. With the floor unit, it appears the only water coming out is a result of gravity when the control is squeezed. Nothing appears to be plugged up with debrie or deposits. There does not appear to be any kind of drive belt for the pump as it seems to operate off the main vacuum motor. Any ideas?


Hi, my name is John I will do my best to assist you.\015\012\015\012Referring to this ... Bissell 1695 PowerSteamer Vacuum

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0675 seconds