Having problems with your Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum ?

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.


Answers :

Repair Help & Product Troubleshooting for Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The extension has lost suction. If I remove the handle tube part, the suction is great to the bendy part, but as soon as I replace the handle part there is none at all and there is no blockage in the handle tube part.


... Dyson DCO3 Absolute Bagless Upright Cyclonic Vacuum

My Dyson DC17 has lost suction on the wand and is not picking up dirt as it should. I have taken the small part at bottom of the machine off to see if there is a blockage--none that I can see. The flexible tube on wand is very tight and won't extend very much. Dyson sent me a new cyclonic part in April but the machine still doesn't seem to be working properly. My serial number is 260-us-d11545. Is there somewhere I can take my Dyson to get it fixed. I'm very frustrated with it. Thank you.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.


Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

Ive a dyson DC05 in perfect working order, but the telescopic tube and the handle are broken, how much roughly should it cost to replace them? And does anywhere sell second hand parts?


Hi there SmartAlec from NelsonVacuums.com.au your post doesn't say where you are from but if you are in Australia then the rod is about $50 and the handle $20. If you are l ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.


Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.


You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

Suction Hose The suction hose has cracked so the suction feature no longer works. I would like to replace it, but cannot find that it is a replaceable part. Hopefully someone else has a solution.


Go to0 http://www.thehooverstore.com/h3000.html there also is a parts break down. You can email them at ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

The handle release pedal wasn't allowing the handle to lower. I took off the pedal and saw the spring load part was broken. What is this part and how to replace it? Bissell 3760-3 handle release


Our vacuum recently had an issue with it's motor, we had to borrow a neighbors a couple times while we were trying to figure out what to do. We decided to take it to a place that specializes in cleaning supplies and cleaning tools to see if they had ... Vacuums

Bissell 2x has suction coming out of the "base" part(when I put my had over the rubber ring that leads from base to the handle part there's suction), but there's no suction coming out of the hose. I'm not certain if there's a clog, 'cause I can't get the hose off.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Replacement part i broke a piece of plastic off my furniture attachment and now it will not spray cleaner or suction. can i get a replacement and will it suction again?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=430575&thid=830386\015\012Replacement part\015\012Posted by blassx3 on Jul 25, 2008\015\012I broke a piece of pla ... Hoover F5906-900 Upright Steam Vacuum

The solution stick inside the handle needs replaced and I would like a new face plate. I have the model numbers (38458-031 & 37275-011), but can not locate the replacement parts. This machine is more than 10 years old and works like brand new. I can not see throwing it out and want to fix it. Please help me locate these parts. Thank you!


... Hoover Steamvac F5860-900 Vacuum

Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.


You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I've replaced the pump and belts. The problem is that I need a drawing or schematic on the routing of the plastic tubing in particular the tubing that comes off the pump and the tubing connection on the suction tube that attaches to the fan housing.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

I have a Flotec shallow well FP4122-08. A burglar stood on the pump this summer to gain access to my goats building (window). There's a small black tube that came off at both ends. When I put the tube back on, it shoots right back off as soon as the pump is plugged in. I don't know the name of the part (tube) to order a new one, and I don't know if it just plugs onto the fittings of both ends, or goes into the pump at the end with the round fitting on it.


... Vacuums

I have a Dyson DC07 animal ( purple). If you are standing behind the vacuum I am missing the lower righthand connection...therefore whatever is suctioned up comes out at that point just over the back wheel. I would like to purchase a replacement for this part. In the manual I believe this part is labeled as C. Can this part be purchased separately ?Please Help....


Hi there SmartAlec from NelsonVacuums.com.au i am not sure if you are based in australia but if you are you can ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Our dustbuster (dont' have model number with me-sorry) won't turn off when I pull back on the switch handle. I disassembled the unit and realize that the tab on the switch handle that pulls back on the internal switch handle to turn it off is not strong enough for its simple task. Does B&D have a proper replacement part?


If you can provide a model number, I can check availability of the switch and can either order it for you, or supply the B&D part number and you can order it from most local vacuum shops in your area or from Black & Decker direct online: ... Black & Decker 15.6 Volt DustBuster Vacuum

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

Dyson vacum cleaner lost suction got the DC14 and it doesn't seem to have much suction in the floor head, the hose still has good suction. I have checked all the paths for blockage and there is none.


Hey, this is Leland with Crucial Vacuum,\012\012If your unit's suction has decreased there could be several reasons.\012\012Firstly, the motor may be the problem. If you hear any noises while the machine is running, you should contact ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0768 seconds