Having problems with your Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum ?

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is.


Answers :

If it is at the on/off switch, you can carefully prise the yellow button out to reveal a torx headed screw. Remove the screw then the housing for the switch can be pulled out which should reveal your loose wire.
\015\012
\015\012Brian
Repair Help & Product Troubleshooting for Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?


You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is.


If it is at the on/off switch, you can carefully prise the yellow button out to reveal a torx headed screw. Remove the screw then the housing for the switch can be pulled out which should reveal your loose wire.\015\012\015\012Brian ... Dyson DCO7 Animal Bagless Upright Cyclonic Vacuum

Dyson DC05 It is a vaccum cleaner in a perfect condition but recently developed a problem. It sparks and sometimes power goes off while operating. It is clear that the wire is loose but do not know how to open the bracket of the main button on the machine. [email protected]


Hi \015\012try this site http://dysonmanuals.llc.nu/\015\012\015\012It has service manuals for the DC05. ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Problem opening up vacuum cleaner to get at power input from cabl


They're very robust you know, if its an upright, start with the screws at the bottem plate unless there's aa way of accessing the cable from the handle, on a cylinder just undo the hefty Philips screws, i don,t think you need a manual, just keep it a ... Vacuums

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?


Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

I have a Filter Queen Majestic canister vacuum cleaner. At the end of the wand, a button to release the attachement not only broke, but also one eyehole on the wand where one nipple on the button falls into. So therefore a new button isn't going to fix the wand because there isn't a hole on one side of the area where the button falls in place for a nipple to secure the button in place. IS THERE A REPLACEMENT PART FOR A NEW SECTION OF THE WAND WHERE THE RELEASE BUTTON IS SECURED IN PLACE THAT I C


... Filter Queen Majestic Canister Vacuum

I have a Chamberlain Liftmaster Professional 1/3 hp garage door opener. I'm unable to find the model number, but it was made in April 2004 and has an orange learn button. It has been working fine since it was new, but now will not open or close when the code is entered on the touch pad. When the problem first started the door would close, but not open. I have tried to reprogram a new digital code, but it does not work at all. There are no problems when opening or closing the door with the re


... Vacuums

I opened the cannister to change the bag and when I closed it the motor switch will not turn on. The second position which turns on the attachment for rugs still comes on. We thougth it was the switch so we ordered the part and it is still doing the same thing. Is there a reset button somewhere inside? The only reset button I see is on the attachment which is working.


It can be a few things. First check the overload protector located on top of the canister. If it has tripped the unit will not run. Push it in to reset. \015\012If that is the problem check the motor safety filter to see if it is clogged and caused t ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

Drive lever the neutral/ drive lever does not engage. seems loose. I have open up the bottom of gear area and have a loose bracket,how does it go back together, need a parts diagram?


Assembly instructions (lots of pictures) HERE. ... Kirby Ultimate G Bagged Upright Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

How best to open casing on Bosch Formula Hygenixx Vacuum cleaner to get at cable winding system to free jammed cable


... Vacuums

I have a Kirby Heritage 84. Great condition except the part that connects the innerbag is missing. I don't even know what it is called. I can open the vacuum cleaner bottom and see that the part is missing. It should be oval where it connects to the vacuum and then extend into the cloth bag. PLEASE HELP!


The Heritage 84 had two different bag assemblies available. One is a dump-out bag. The dirt simply dumps through the bottom. The other is the bagged style which has a full length zipper to open it. Inside it should contain a "bag fill tube", and a to ... Kirby Heritage II Vacuum

BOSCH ERGOMAXX MODEL BSG82000GB/01 BAGGED VACUUM CLEANER NOT WORKING AFTER VACUUMING MY CAR, CHECKED FUSE IN PLUG AND CABLE WIRES ALL OK, I SUSPECT THE MOTOR HAS OVERHEATED BUT THE MACHINE JUST WENT DEAD JUST AS IF YOU PRESSED THE OFF BUTTON, NO SMOKE OR BURNING SMELLS??? PLEASE CAN ANYONE HELP.


... Bosch Vacuums

The TechDrive Pedal on my Kirby G6 fell out of the back of my vacuum cleaner. I removed the screws from the metal plate one the bottom to try to see if something had come a loose. Can you send me a diagram so I can put it back together or tell me where I can get a service manual. The only part I am having trouble with is the metal piece inside that engages the power drive. Thank you.


The pedal drive fell out . Do you have a manual telling me how to get it together again.. Thanks, Dianne ... Kirby G6 Bagged Upright Vacuum

We have a Kenmore canister vacuum cleaner 25614504. It has in intermittant light and power flicker in the power mate unit as it is moving over the floor. This behavior can be simulated by jiggling the power cord where it eners the power mate. I do not know how to enter the power mate to see if there is a loose wire.


... Kenmore 28614 Canister Vacuum

I have a dyson dc04 vaccuum cleaner and i want to replace the cable to the switch how do you get to the switch


Hi there SmartAlec from NelsonVacuums.com.au here. This is a bit of a tricky one on your first go so be gentle. Basically what you have to do is lift off the switch cover t ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

I have an endurotronic 4111 electrolux vacuum called ''the boss'' and the cable wont retract into the vacuum when i depress the button on the top. how do i dismantle parts to have a look to see if it will repair or not. does anyone have a repair manual for this vacuum. thx


... Electrolux Vacuums

I have power at top of handle, thus start button light up. but when turn on nothing happens. I checked wiring and it all seems plugged in. The lights on the bottom of the cleaner (part of the base) don't light up. so somehow it makes since issue at base. HELP.. retired cop


Hi,\015\012Seems, the motor of vacuum has no power supply ( not connected yet). You may have a loosen/defective connection on motor cables/terminal. Please check and have it fixed. ... Oreck XL2200 Bagged Upright Vacuum

Hi I’ve got a Panasonic vacuum cleaner MC E468 1600W a few years old now but works well up to recent problem. Not picking up I checked the obvious things and found excessive air being sucked in around the hose housing at the back of the vacuum (as it enters the waste bag) On inspection it appears to me as if there should be some sort of gasket that may have perished and been sucked in, however I can’t identify any such part. Any thoughts on what the problem/solution may be will be appreciate


The hose on the back might be loose - check to see that the hose is not obstructing anything where it screws in at the back - or indeed the screws may be loose themselves; some of the MCE 468 models had an additional ring washer that sits between the ... Panasonic Vacuums

Replacement parts where can i find replacement steam pocket towels online for the shark ultra steam blaster hard surface cleaner? I went online to www.sharkcompany.com & www.sharkvac.com and when I enter my model number S3325 search comes back with 0. Thanks


You can found them on amazon, take a look here: Amazon com Euro Pro S3325. I hope this was helpful. Cheers ... Euro-Pro S3325 Handheld Steam Vacuum

Contour Flexihead, I have a loose connection around about the cable entry. How do I open it. 3 Svrews removed but nothing comes apart


There is a solutioln on your web ... Electrolux Vacuums

I have a EuroPro SC410 steam cleaner. It produces steam, but the steam button does nothing but cause the unit to hum. If there is valve to allow the steam to exit, is not working. I would like to replace it, where can I purchase the parts?


... Euro-Pro S3325 Handheld Steam Vacuum

I caught a shoe lace in my Dyson DC17; pulled it free, opened the brush/roller area and cleaned everything but the brush still won't work. Read somewhere that there is re-set button but the only one I found was to switch between the brush / sweep functions. Is there a fuse / connection / part that may need to be replaced?


I don't believe so. Keep trying the reset button. Sometimes the reset sticks. Hope this helps. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0676 seconds