Having problems with your Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson ?

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Answers :

Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it.
Repair Help & Product Troubleshooting for Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

On a Kirby sentria the metal spool sticking out that goes into hose or power head becomes extremely hot and left burns marks on brush tube. It only gets hot when using power head. I checked all adjust


Check the brush roll to be sure it's spinning free too much drag can cause that to get hotter but usually it would break the belt. That spindle will get hot from the friction created by turning the belt and from the motor's heat. They'll just get hot ... Kirby Vacuums

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

I have a kemore progressive canister vacuum and the power head connects enough to the hose where the head accnoledges it's connected and the brush spins BUT i can't get it to lock in so i have


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

Where can I get a new power head and hose for this vacum


The Eureka central vacuums generally have standard inlets. You can use any brand with what you have. The most important thing you will need to decide on is electric vs non-electric. The brands attachments I would recommend are Imperium, Beam, and ... Eureka 1810 Central System Vacuum

Beam solaire hose only works to suction The power head isn't working. Have another hose and the power head does work on that one so I know it is the hose


... Vacuums

E series power head handle, internal wire came lose


Here is a pix.\015\012\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

I recently lost power to the power head. Thinking the hose was not sending current to the head, I bought a new hose. It did not solve my problem. I have since noticed that a warning symbel is appearing that indicates what looks like a key with TA inside. The vacumn has good suction. Please advise John.


Hi\015\012\015\012Please check the link bellow to diagnose your problem…..\015\012\015\012http://home.howstuffw ... Electrolux Epic 6500 Vacuum

Dirt Devil M082475 12 AMP cannister vacuum power-head problem


Theres no fuse, you will need a new hose ... Bosch 12-Amp Formula Canister Vacuum with Hepa Filtration Bagged Vacuum

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on


... Miele Blue Moon Bagged Canister Vacuum

I have a tank style vacuum. When I vacuum with the power head it dims and slows down when I push the power head back and forth, but it powers back up louder when I stop pushing it If i remove the powerhead from the hose the vacuum works fine.


Most likely the belt. Thats the cheapest so try it first ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!


... Miele Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?


Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

We have inherited a Filter Queen Majestic Triple Crown Model 99C vaccum and have no owners manual stating the year it was purchased and parts available. Our power hose electic wire connection (about 6 inches long) which plugs into the main unit is split in the hose attachment end. The motor sound went instantly quieter and I wondered if this was why when I found this frayed electical wire. It has not been used since this problem was found. How much is this single replacement part? I live


... Vacuums

Dyson dc05 power head not working. Fitted new hose and power head


Please go to http://www.dyson.com/support/help.asp?article=32&product=DC22-MOTORHEAD-USplease select the model exactly, and proceed with common sense for troubleshooting problem and fix it.You must shure to see the videos, and see if the ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

CANISTER IS GETTING POWER BUT NO SUCTION FROM HOSE AND DOESNT SEEM LIKE THERE IS POWER GOING TO HOSE..I HAVE CLEANED OUT THE FILTER AND CHECKED ALL BREAKERS...


Hello,Carnister vacuum cleaners are all built with the same \015\012principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are ... Hoover S5615 Hush Central System Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.


I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

I have an S3630 Hoover Windtunnel with a Mach 6.1 power head. One of the wheels on the back of the power head broke off. I will need the back under pannel with the back wheels. Where can I get these parts?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0926 seconds