Having problems with your Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow ?

My dyson hand held shuts down after about 30 seconds, It turns back on again, but it does this over and over again, even after being fully charged with caontainer emptied. Its almost like an overheating thing, but different since it starts right back. It is annoying.

Answers :

Repair Help & Product Troubleshooting for Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dyson hand held shuts down after about 30 seconds, It turns back on again, but it does this over and over again, even after being fully charged with caontainer emptied. Its almost like an overheating thing, but different since it starts right back. It is annoying.

... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

My hoover elite rewind does not pick up dirt like it should. how do i check for a clog? I can hear it picking stuff up but when I empty the cannister there isn't much in it. today it shut off like it threw a breaker. I let it sit and plugged it back in and it started working again. don't know if the problems are related or not. any suggestions??

Have you cleaned the inside filter? Open the cup hold on to the yellow piece in the center and twist it to unlock (there are arrows on the pieces to show how far to twist). Take the filter out and try to clean as much of the debris off of it. ... Vacuums

Hi. I have a Kirby from back in the early 90s (model G3D). Never had major issues with it. Can't remember the last time I had maintenance/tune up done. It's just sounding different when I run it the last few times...almost like it's louder and kind of echo-ey. Still suctioning well, but something's not right and I don't want to run it until I know if anything's up. Any suggestions? I'd like to try and figure this one out on my own with your help. Thanks in advance for your help. Marci

Check the belt. this is a strong vaccume and even without the belt it will still have a decent amount of suction. If the belt is not tight or intact it can let the motor turn faster which will sound louder. other than that check all the hoses for hol ... Kirby Ultimate G Bagged Upright Vacuum

I have a genie hoover and would like to know how I get the purple bit back onto hoover as I emptied the filter and I can't get it back on need help fast???

... Vacuums

Tristar mg2 keeps shutting off and a few minutes later comes back on. Almost like it is heating up. I noticed that intermittently I'm losing suction.

. remove the hose and check hose and wand for blockage by dropping a coin through end to end. A coin will come to rest against a clog and when you shake the hose the coin will rattle in the are of the obstruction. Blockage should always be draw ... Vacuums

My filter queen just had the motor rebuilt last year and was basically a brand new unit when I got it back. It is not picking anything up now when I vacuum. The beater bar on the carpet attachment is turning fine and when I take all the attachments off the hose I can feel the suction being created like it should be picking up debris just fine. I have emptied the canister even when it did not have much in it; however, it still will not pick anything up off the carpet. It picks up debris tempo

It sounds as if you have a clog inside the "Power Nozzel". They mention that there are "no user serviceable parts within the Majestic® Power Nozzle" My advice would be to see if you can see a clog with in reachable distance and try to remove the ... Filter Queen Vacuums

I have a Kenmore Progressive Upright Vacuum - Purple, and it worked just fine. I emptied the canister (like always) and put it back in place. I turned on the vacuum to it immediately shutting down (motor) and only the lights come on. There is no movement/noise/suction at all! Any suggestions? I have tried everything. I have no idea why it did this.

Make sure that something didn't fall into the fan assembly in the base when the canister was removed. The motor should have an overload reset switch. Try moving the motor manually (power plug out) to make sure that it isn't bound up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I don't feel that the vac is close enough to the carpet anymore .. it's almost like I have to push the head down so it reached the carpet to roll the brush through it ... I've tried a friends vac and it shows nicely that you've just vacuumed the carpet .. heavy traffic areas are not getting pulled back up .. I have the short shag type carpet .. Thanks

Consider disassembling and cleaning your unit. Sometimes dirt and grit will build up, and when wiped away allow the moving parts to function better. Dysons are made to be broken down by the homeowner. A manual can be obtained here: http://www.manual ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brush roller on my vacuum will not move. I've cleaned it, checked the belt, but when I put the roller back it, it will not move...almost like it is in a locked position. Everything has been done correctly from the book yet, it still does not move. Any help PLEASE?

... Electrolux EL8502 Versatility Bagless Upright Vacuum

Vax Ultima Cyclonic upright vaccuum makes a horrendous noise since it was emptied a while back. I have changed the belt as it sounded like that slipping, but it didn't help. Brushes fine, just very, very noisy. Any ideas?

... Vacuums

Brushes don't turn. Don't know how to take bottom off. This is an almost new machine. Wonder if it has to do with the change in air flow from when you use the tube and then go back to regular. I feel like it is quite simple but can't figure it out. Thanks so much Judy

Hi Judy. If its new then I bet you its to do with the clutch. \015\012\015\012See the knob on the bottom of the machine. You use this to switch the Brushbar off and on. You can switch it off so that the brushbar wouldnt scratch a wooden f ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor

On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum

My shop vac won't turn back on after emptying

I'm afraid you'll need to take it apart. the switch is mounted in a plastic holder in the top.\015\012While you got it apart and without it plugged in, check to see that both brushes are touching the commutator. there should be sufficient spring ten ... Shop Vac 925-13 Canister Wet/Dry Vacuum

Hi! I have a Pfaff Creative 1475. The presser foot seems "gummed up" or stuck. The back lever lifts it with great force, but then instead of staying up like the lever usually does - it then falls back down. The lifting foot stays stuck up and I have to push on it to get it back down. Help?

Bdfbjhfjffjfjfjfjfjfjfkfjfjffjfjfjjfjfjfjfjff ... Vacuums

My power cord will not retract back into the housing< i would like to open the back of the unit but there no screws or bults to due so. How do you open the back of model c151d

Try standing vacuum on end, then gently tugging and releasing cord. This generally will retract it.\015\012There are many problems that can result in disassembly and reassembly by an untrained person, including shock and fire. For those and o ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.

... Broan-NuTone VX475 Bagged Central System Vacuum

I have a bissel proheat carpet cleaner. THe trigger is stuck in the on position. However, no water or shampoo is coming out. I can pry it back out but it feels like a spring is missing or something like that.

You may need to replace the handle assembly, or at least take it apart and reconnect the spring inside the handle..here is the repair manual, which has good illustrations on page 9 and 22 of working on the handle..http://newz ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Spits dirt back out at me as I vacuum, seems like there is a big gap when tilted back

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Spits dirt back out at me as I vacuum seems like there is a big gap when tilted back

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.

You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Filter I bought this Hoover a few years ago-- just now about to use it first time. I cannot find my user's manual and don't know how to change the filter-- or to clean it or whatever I am supposed to do with it. Also, there is a handle on one side of the unit that seems to be attached to an empty chamber or canister kind of thing. It looks like it should pull out, but it does not budge. I really would like to have a manual, but can't seem to find one. Is there a similar model that is still

This is not for the exact same model, but should help you out:\015\012http://edge.maytag.com/epipubs/56511B47.PDF ... Hoover U8143-900 Upright Vacuum

Was hoovering when my DC04 made a funny high pitched noise then a whirring noise, this was accompanied by a smell of burning and a puff of smoke! Almost sounds like it might be a clutch slipping, is this possible or is it more likely to be a motor burn out?

OK... the DC04 doesn't have a clutch. My best guess is that the belt that drives the brush roll has broken. The smell of burning and smoke puff were probably caused by the motor suddenly speeding up when freed of its burden of driving the brush roll. ... Vacuums

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...

The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No

Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0446 seconds