Having problems with your Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow ?
Tilt to vaccum spring fell out
\015 3 parts fell out\015
Repair Help & Product Troubleshooting for Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Tilt to vaccum spring fell out
... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.
I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I am working on repairing a model S3101W shark steam mop. I took out two screws and took off the swivel head and a short clear plastic tube fell out. I do not know where it goes. No spring fell out with it. Where does it fit? What holds it on. Thank YOu
The same problem Im having, and Im not a handy person at all..Im about to junk it..I have no idea what Im doing :) ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
Eureka as1000 spring fell off carpet adjuster
Carpet Height Adjust Broken - Spring fell out
... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
Miele cat and dog 5000 poor suction because spring fell out from somewhere
... Miele CatAndDog700 Bagged Canister Vacuum
2001 kirby G6 vacuum wheel fell off. where does the spring go when put back together?
Here are some diagrams that may help you of the G6http://www.vacpartswarehouse.com/Kirby-Generation-VI-G6-Upright-Vacuum-Cleaner-s/ ... Vacuums
Spring fell out of dyson dc25 vacuum
... Dyson Dc25 Animal Upright
I have a Dirt Devil M088400 - Vision Turbo Vacuum. A spring fell from the bottom and the carpet height adjust isn't working. The rollers under the unit won't stay in place either. Can you tell me how to put the carpet height adjust back together?
The roller attaches to wheels. There is a spring that attaches from roller to hight adjustment selector which is a plastic peice with a little hook on bottom that spring attaches to. Both peices should have a hook that the spring ttaches to. ... Dirt Devil Vacuums
Can't get my Miele Power Brush SEB 236 Back together. Height adjustment mainly. Not sure where 1 loose spring goes either and which screws go where. Got it back together and had 3 left, then a 4th fell out when I vacuumed.
... Kenmore Vacuums
Spring fell out dyson - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Hi there,I am sorry to hear you are having difficulty with your DC17 switch. We recommend a switch repair or replacement be completed by an authorized technician. Because of the location of the spring it may need to be installed at an authorized ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I had to replace the handle. The wiring is inside the handle. I would like to verify the position of all the switches and the location of a spring that fell out.
Dear Heidimtaylor,\015\012\015\012For this first we will required your model no. I will advised you too visit the following site and search for your model's service manual. It contains details which you required. Following link will help you... ... Vacuums
My front wheels fell off how do I fix it. there is a slender long spring and I don't know where it goes
That spring connects to a slot beside the height adjuster knob and a hole in the base to the wheels that fell off.The problem is you can't get the wheels to go back in flush so the height adjustment works.The vacuum will not be close enough to the fl ... Eureka 2997AZ Bagless Upright Vacuum
Hoover model U6476910 I was cleaning out the bearing sections of the brush when a spring type pressure washer fell on the floor. I did not see the washer when I took it apart and I can't tell where it goes in order to put it back together. It is very thin and measures about 5/8 inch with an 11/32 inch hole. Frank Nething
Hi frank this sounds like its a compression washer, you normally find these on the end of the roller to even out any movement from side to side, as you look at the hoover's brush head, it should slip into a groove on one side with the roller...hope t ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Dear tech, I have a 12amp bissel bagless cleaner model# 4220-P the part i need is under the foot lever to lower the vaccum cleaner to sweep. The part is the slide pin that locks the sweeper from lowering.It has a spring attach to it. can I buy this part bob Yurkovich
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=805734\015\012Generic problem for all Vacuums\015\012Dear tech, I have a\015\012Posted by yurk on Jul 1 ... Vacuums
Small rubber cap that fits on nipple at bottom of solution tank came off, spring and check ball fell out. What's the order of reassembly? Also, can I glue the rubber cap to the nipple to prevent this in the future?
May I get the model # to help you more ... Bissell 1720-1 Little Green Wet/Dry Vacuum
Height adjustment not working i have to tilt vaccum ack to get rushes turning. thinking i can fix it ut don't know..
This usually means your belt is worn. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b
A small spring and a black plastic part fell off the handle release pad
... Hoover Floormate H3000 Upright Wet/Dry Vacuum
When vaccum is tilted back suction does not engage.
This can happen if two tiny wires that are connected to the circuit board and lead to the beater bar are broken. These wires brake where they go through a black rubber grommet. You need a torx screwdriver (No: 15) to remove two plastic covers to acce ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
The height adjustment lever and left front wheel fell off my kirby g3 where does the spring go? do you have a schmatic?
... Kirby Ultimate G Bagged Upright Vacuum
My bissell 3910T won't stay upright. Is there a spring that may have fallen off?
... Bissell 3910 Bagless Upright Cyclonic Vacuum
4870 GZ torsion spring reinstallation
... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Dyson vaccum does not balance properly
Check within the manual: Dyson Dc15 Manual ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Wheel and lever fell off Kirby ultimate G
The spline shaft is probably worn. you will have to replace the assy. ... Kirby Ultimate G Bagged Upright Vacuum