Having problems with your Dyson Vacuums ?
Losing suction in upright position
\015 Seems to be losing suction in upright position, but still picks up well with the hose attachment.\015
It's probably your belt. It could be broken or stretched. If broken or stretched, the roller won't spin very well, if at all. Another possibility is that there may be debris blocking suction near the roller. Hope this helps.
Repair Help & Product Troubleshooting for Dyson Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Losing suction in upright position
It's probably your belt. It could be broken or stretched. If broken or stretched, the roller won't spin very well, if at all. Another possibility is that there may be debris blocking suction near the roller. Hope this helps. ... Dyson Vacuums
Dyson animal loses suction when I let the handle down from the upright position to use, I've cleaned the foam filter, and the plastic filter holder and dried thoroughly, removed and cleared the right side U-bend, and the center, rear U-bend access, also made sure nothing was in the way of the beater bar. Any thoughts? thanks. lorri
Is the noise a loud screaming or a grinding/vibration? The screaming is an air flow problem and you'll want to check your hoses are clear and all the seals are tight. The grinding is an issue with the roller/belt/clutch/motor/housing. From what I'm r ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dyson DC14 Animal Vacuum - Loses suction in the reclined position. Works fine upright with the wand. Any idea what the problem is? Thanks
Check the brush bar is turned on, read this article: DC14 clutch and brushbar\015\012\015\012Then check the small h ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.
Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis
U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Vacuum won't **** in upright position, but there is suction from the hose in the upright position
Theres a knob that switches it from floors to carpet turn the to floors.please leave feedback ... Vacuums
Hi...there is no suction in my upright's hose...there is suction when regular carpet cleaning but when I put it in an upright position and take the hose out there is extemely light suction.
... Miele S7210 Bagged Upright Vacuum
When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond
Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums
Dyson won't go back into upright position to engage suction
The dyson.com website had a solution for this particular problem. Just press in a button in the area around the right wheel while lifting the rear of the vacuum up. This allows the base to roll forward enough to go back into the upright position. I ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
No suction in an upright position
Mine is doing the same thing-- did you ever figure out the solution? Thanks!! ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
No suction in upright position
Check the adapters at the bottom. They're supposed to move cleanly when you lower the handle. It's pretty obvious if there's an air gap when you lower the handle, and you should hear the suction in the air gap.And...call Dyson...their sup ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The suction only works when upright, when in the recline position there is no suction and it starts to smoke
You probably have suction just no aggitation. those units use a clutch assy with two belts unfortunately when the belts fail you have to replace the whole assy just like everything else on the dysons. check your brushroll for rotation and for hair wr ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
DYSON DO4 ABSOLUTE. HAS POOR SUCTION AT REVOLVING BRUSHEAD, BUT IN UPRIGHT POSITION USING TOOLS SUCTION VERY STRONG. NO BLOCKAGES AND B ELTS INTACT
Dyson dc07 suction when upright but no suction when tilted in operate position
I had the same issue and solved it easily.My experience is the same as the March 6th response/ When you push your foot onto\015\012the base and then recline the handle, use your toe to gently push the\015\012very front of the base down closer to the ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Suction perfect when in upright position, but when tilted to actually clean there is total loss of suction - cannot see blockage anywhere. Thanks for your help.
If you are confident there are no blockages, look underneath, where the brush is, and you will see a short length of reinforced clear plastic hose. This often develops a split which results in loss of suction. You can pull the hose off at the motor e ... Dyson DC07 Bagless Upright Cyclonic Vacuum
No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.
Generally, the problem is that the belt is not running the brushes. This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed. This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
The suction is fine in the upright position; however, if I try to vacuum the suction go away. I have check for clogges.
Did you check down in the brush head for clogs? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
When I engage the vacuum cleaner by going from the upright position to the slanted position there is loss of suction.
... Dyson DC07 Bagless Upright Cyclonic Vacuum
My dyson has suction with the handpiece, but makes a horrible noise when using it upright. The roller does spin in the upright position. Help!
... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum
BURNING SMELL My DC 07 has suffered from poor suction in the upright position for some time now but this morning it ground to a halt. It was if the motor had burned out. I turned it upside down and some small stones etc tumbled out. I tried switching on again and the motor kicked in but the smell was horrendous so i switched off immediately. If it's likely to be **** inside the motor area i don't no how to access it. I've removed for fixing screws but still unable to prise apart. Is it just the
Hi.\015\012\015\012Try this site http://dysonmanuals.llc.nu/ has service manuals covering removing the Dc07 motor. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
No suction in the wand and the vacuum shuts off in the upright position. Just bought a new filter
The wand is clogged. shuttimg off sounds weird. but maybe your cord or something is hitting the off switch. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Loses suction after a few seconds - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Look for a clog somewhere between the suction head and the bag ... including the bag.\015\012 ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?
Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have a new bissell 50c9 upright vacuum and it keeps clogging in the clear window in the back. there is a flap that keeps coming open and filling up. everytime i clean and restart, the flap opens. i tried holding it closed and noticed lose of suction.
Shuts off at upright position also has lost suction. I have already cleaned the filter
Check for a clog ... Vacuums