Having problems with your Dyson Vacuums ?

I have a DC07 Animal and the roller stopped rolling. I appears that the roller sheared off on one side.


Answers :

Your belt could be torn or the teeth could be worn off. Contact dyson for a local repair rep.
Repair Help & Product Troubleshooting for Dyson Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a DC07 Animal and the roller stopped rolling. I appears that the roller sheared off on one side.


Your belt could be torn or the teeth could be worn off. Contact dyson for a local repair rep. ... Dyson Vacuums

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Eureka TRUE HEPA Whirlwind Bagless same problem seems...roller just stopped...took everything apart and turned it on just in time to see belt melt...I was able to get the end caps off both sides at first and now can't seem to get the one side. Really love this vacuum! Don't want to have to part with it!


If you are able to remove one end cap, the brush roller shaft can be removed and the other bearing is exposed for examination and removal of the hair that probably is clogging it. After cleaning and reassembly the brush roller should rotate freely. C ... Eureka 2961AVZ Bagless Upright Vacuum

Roller is not rolling-belt missing - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


You need to take of the base plate then take out the roller then put a new belt in then put the roller back in ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Roller problem Roller keeps stopping. I've emptied the dustbin. removed the roller to see if it is clogged, but appears to be nothing impeding it.  It stops on a short napped rug, and even on the wood floor.  Is the spool that the roller slips into driven by a belt? Can I get in there behind the spool?


I have 3 Prontos, one in each part of the house. Two of mine had the rollers stop. I figured out the problem and it fixed both. Take the roller out by turning the plastic screw and popping the plate off. Pull all debris off the wheel that turns. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

Brush roller stopped rolling


My daughters is doing the same thing and the plastic at the ends of the brush bar melted just enough for it not to turn properly. You might want to chech that. ... Eureka 2961AVZ Bagless Upright Vacuum

Dyson 17 DC Animal - hit a nylon strap that got stuck in the roller. Removed strap but roller made noise when engaged, now roller not engaging but rolls free when turned manualy.


It could be the belt. Here is the replacement belt you need:Dyson DC17 Belt ... Vacuums

DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>


I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My dirt devil easy lite cyclonic does not suck up the dirt or anything on the floor anymore the rollers still roll. It stop sucking.


Check and make sure that the pickup tube from the bottom of the sweeper to the waste cup does not have a clog anywhere you can use a metal coat hanger and straighten it out and carefully run that thru. ... Vacuums

I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.


... Vacuums

I have a dyson animal dc24. It is 7 months old and has stopped working. The hand tool is working fine but when I insert it to engage in normal vaccuming the suction stops. I can hear a strange air sound. Also the brush is spinning but it is not picking up. I have taken it apart and checked for a clog but I don't see one. Any advice?


Hi there,I'm sorry to hear your DC24 Animal isn't picking up as well as usual. Although I note you've already checked for blockages, it sounds as though this is likely to be the cause of the issue.To locate and remove any blockages, p ... Vacuums

DYSON DC07 ORIGIN BRUSH ROLLERS WONT ROLL WHEN HOVVERING BURNING SMELL AND SMOKE FROM BOTTOM OF HOVER ROLLERS WILL MOVE BY HAND ANY IDEAS, THERES NO BLOCKAGES.


Hi There, Ok so I have made a few videos about what to check when you have issues like this. THere are 3 possible causes. 1. THe bearings in the brush roller are worn so even though you can turn it by hand the belt cannot.2. The clutc ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson 28 animal. When I start the vacuum the roller spins for a couple of seconds the stops. I have to turn machine off and on again then the roller will work for another couple of seconds.


... Dyson DC28 Animal Bagless Upright Vacuum

This is not an electrolux problem, but I am hoping one of the experts can answer the question. I have a Sears air compressor that suddenly stopped working. After looking at how the motor case is put together, it appeared that it would essentially have to be destroyed to get it apart and into the motor. I received a new compressor for my birthday so I decided to tear into the old one to do some diagnosis. After getting into the case where I could see the motor/pump, I have discovered the prob


This is intersesting. I think the fuse is simply a heat sensor. If you by pass this the only problem you may run into is if the motor over heats it my eventually burn out. However, for what you are using it for overheatin should not be an issue. This ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You


Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Looking for the roller part number for Eureka 2961AVZ. The ball bearing on one of the side broke on the existing roller.


You should be able to find the roller you are looking for at this URL:\015\012\015\012http://www.vacuums24x7.com/eualseup29se.html\015\012\015\012Paul ... Eureka 2961AVZ Bagless Upright Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?


I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

There's a strip of pet hair that doesn't get picked up only on the left side of the roller, like it's rolling all of it up and kicking it out that side. I have to work from right to left to get it all up. is this a suction problem?


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.


Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Roomba My Scheduler started making a "grinding" noise every now and then until one day it just started grinding and then stopped (I could restart the unit, however it repeated the grinding and stopping). I have checked the wheels and all of the gears appear to be in good order. I have a hunch the brush motor may be stripped. Any opinions? Thanks: RAnderson


Hi!\015\012\015\012Further investigation (running diagnostics mode) revealed the impeller (in the dust bin) was out of whack. I got another dust bin from EBAY and replaced the impeller and motor. Unit works fine. ... iRobot Roomba 4210 Bagless Robotic Vacuum

My power head (carpets) does not rotate at all. I have called Dyson and they walked me thru a series of steps to make the roller move, which initially worked, but now when it rolls it's really slow and stops rolling.


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hi. I have a DC 24 which when brush rotates makes a very loud noise. I have replaced the brush and side bar. The side bar appears very loose. The noise stops when I switch the brush rotation off. Any ideas ?


Hi there,I'm sorry to hear you're having difficulties with your DC24. If the cleaner head seems to be making an unusual noise during use, you may want to check all the parts are correctly assembled, and that the cleaner head and brushbar are ... Dyson Ball DC24 Bagless Upright Vacuum

Roller brush isn't rolling it seems to be stuck.


... Oreck XL2200 Bagged Upright Vacuum

My dyson animal is hard to push on carpet - the beater bar is still operational. When I turn off the beater bar and run the vacuum on hardwood the beater bar stops moving, but it still ''rolls'' on the hardwood - it doesn't pull up like it used to. It also seems to not be picking up as well as it used to, although no blockages are present and the filter is clean.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1012 seconds